Results 171 to 180 of about 15,690,564 (314)

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Engineering Deformation and Failure in Diamond Triply Periodic Minimal Surface Lattices via 3D Wall‐Thickness Grading

Advanced Engineering Materials, EarlyView.
The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza, Danilo Bruson, Manuela Galati, Luca Iuliano   +3 more
wiley   +1 more source

A Geometric Approach to Average Problems on Multinomial and Negative Multinomial Models. [PDF]

Entropy (Basel), 2020
Li M, Sun H, Li D.
europepmc   +1 more source

3D‐Printed Serial Snap‐Through Architectures for Programmable Mechanical Response

Advanced Engineering Materials, EarlyView.
A serial snap‐through architecture is realized using compact 3D‐printed von Mises truss units arranged in a staged cascade. Their geometry and boundary conditions program multistage mechanical responses with plateaux and re‐hardening regimes. An inverted‐compliance model predicts these behaviors and enables analytical design of programmable force ...
Filipe A. Santos
wiley   +1 more source

Exploring Dipolar Dynamics and Ionic Transport in Metal‐Organic Frameworks: Experimental and Theoretical Insights

Advanced Functional Materials, EarlyView.
In this study, the interplay of dipolar dynamics and ionic charge transport in MOF compounds is investigated. Synthesizing the novel structure CFA‐25 with integrated freely rotating dipolar groups, local and macroscopic effects, including interactions with Cs cations are explored.
Ralph Freund, Arthur Schulz, Peter Lunkenheimer, Maryana Kraft, Thomas Bergler, Harald Oberhofer, Dirk Volkmer   +6 more
wiley   +1 more source

Analyzing Electronic Excitations and Exciton Binding Energies in Y6 Films

Advanced Functional Materials, EarlyView.
The Y6 molecule is used for increasing the efficiency of organic solar cells. The exciton binding energy is calculated for ensembles of Y6 molecules that are representative of the typically used films. The calculations show that the excitons typically spread out over many molecules.
Sahar Javaid Akram, Sophie Meißner, Stephan Kümmel   +2 more
wiley   +1 more source

Enhancing Optoelectronic Properties in Phthalocyanine‐Based SURMOFs: Synthesis of ABAB Linkers by Avoiding Statistical Condensation with Tailored Building Blocks

Advanced Functional Materials, EarlyView.
A novel phthalocyanine (PC)‐based metal–organic framework (MOFs) is synthesized using ditopic PC linkers obtained through regioselective statistical condensation. The resulting MOF exhibits significant improvements in electronic absorption, thereby enhancing the material's performance in light harvesting and energy conversion.
Lukas S. Langer, Mareen Stahlberger, Xiaojing Liu, Yi Luo, Niklas E. Häußermann, Puja Singhvi, Yidong Liu, Olaf Fuhr, Martin Nieger, Lars Heinke, Thomas Heine, Christof Wöll, Stefan Bräse   +12 more
wiley   +1 more source

Unique Performance Considerations for Printable Organic Semiconductor and Perovskite Radiation Detectors: Toward Consensus on Best Practice Evaluation

Advanced Functional Materials, EarlyView.
A lack of standard approaches for testing and reporting the performance of metal halide perovskites and organic semiconductor radiation detectors has resulted in inconsistent interpretation of performance parameters, impeding progress in the field. This Perspective recommends key metrics and experimental details, which are suggested for reporting in ...
Jessie A. Posar, Matthew Large, Andrea Ciavatti, Laura Basiricò, Beatrice Fraboni, Paul J. Sellin, Attila J. Mozer, Marco Petasecca, Matthew J. Griffith   +8 more
wiley   +1 more source

EVO: A Geometric Approach to Event-Based 6-DOF Parallel Tracking and Mapping in Real Time

IEEE Robotics and Automation Letters, 2017
Henri Rebecq, Timo Horstschaefer, Guillermo Gallego, D. Scaramuzza   +3 more
semanticscholar   +1 more source