Results 151 to 160 of about 43,204 (241)

Geometric Calibration Using Line Fiducials for Cone-Beam CT with General, Non-Circular Source-Detector Trajectories. [PDF]

open access: yesProc SPIE Int Soc Opt Eng, 2017
Jacobson MW   +8 more
europepmc   +1 more source

Dual‐Site Ru Single‐Atoms and RuP Nanoclusters on N, P, and B Co‐Doped Porous Carbon for Efficient Alkaline HER and AEM Water Electrolysis

open access: yesAdvanced Functional Materials, EarlyView.
Ru single atoms and RuP nanoclusters are co‐anchored in N, P, and B co‐doped porous carbon nanospheres via in situ carbonization/phosphidation of a boronate polymer precursor. RuP activates water, while nearby Ru single atoms accelerate H2 formation through H* transfer. The catalyst delivers low overpotential and high durability in alkaline HER and AEM
Xiaohong Wang   +13 more
wiley   +1 more source

Prenucleation Species Dictate Foreign Ion Incorporation in the Biomineral Precursor Amorphous Calcium Carbonate

open access: yesAdvanced Functional Materials, EarlyView.
ACC forms via aggregating prenucleation clusters that gatekeep its chemical composition. Ion identity steers the path: Ba and Sr substitute Ca in clusters, thereby inhibiting nucleation, with a dose‐dependent switch of Sr to induction. Mg partitions into Mg‐rich and Mg‐poor clusters; the latter form ACC, expelling Mg.
Qianyu Zhao   +9 more
wiley   +1 more source

Actuating and Sensing Composites of Liquid Crystal Elastomers and Poly(ionic liquid)s

open access: yesAdvanced Functional Materials, EarlyView.
Ionic conductive, mechanically tough, flexible, and stretchable filaments of a composite material comprising a liquid crystal elastomer and a poly(ionic liquid) are produced through 3D printing, which exhibit large actuation strain under stimulation and electrical resistance variation in response to deformation or environmental condition changes. Their
Zeping Liu   +6 more
wiley   +1 more source

From Clinic to Computation: Multiscale Bioengineering Strategies for Durable Biological Aortic Valve Replacements

open access: yesAdvanced Functional Materials, EarlyView.
Bioprosthetic aortic valves have revolutionized the treatment of aortic stenosis, but their durability is limited by structural valve deterioration (SVD). This review focuses on the pericardial tissue at the heart of these valves, examining how its mechanical properties and calcification drive fatigue and failure.
Gabriele Greco   +7 more
wiley   +1 more source

Breathable Graphene Oxide‐Polymer Composite Membranes With Two‐Step Barrier Mechanism Against Nerve Agents

open access: yesAdvanced Functional Materials, EarlyView.
ABSTRACT Breathable membranes that reject chemical warfare agents (CWAs) are required for next‐generation protective apparel. A dual‐function graphene oxide (GO)‐polyamine architecture is introduced that addresses the long‐standing tradeoff between vapor transmission and CWA selectivity.
Hyungjun Kim   +6 more
wiley   +1 more source

Electro‐Chemo‐Mechanical Coupling in Hf0.5Zr0.5O2 Ferroionic Heterostructures

open access: yesAdvanced Functional Materials, EarlyView.
Schematic of a ferroionic HZO heterostructure where epitaxial interfaces enable dynamic oxygen‐vacancy exchange, coupling ionic and ferroelectric degrees of freedom. Vacancy‐mediated polarization modulation biases HZO polymorphism, suppresses leakage, and enhances piezoelectric response, yielding distinct butterfly‐loop evolution and diode‐like ...
Achilles Bergne   +17 more
wiley   +1 more source

Effects of Molecular Designs and Double‐Network Morphologies for Bioadhesive Semiconductors

open access: yesAdvanced Functional Materials, EarlyView.
This study establishes molecular‐to‐mesoscale design rules for bioadhesive semiconducting polymers (BASCs). It identifies how side‐chain length, double‐network formation, and film thickness modulate adhesion strength and electronic performance, providing insight into the rational design of intrinsically adhesive semiconductors for stable and efficient ...
Zhichang Liu   +8 more
wiley   +1 more source

4D‐Printed Magneto‐Plasmonic Microrobots for Programmable Spatiotemporal De‐Icing

open access: yesAdvanced Functional Materials, EarlyView.
A 4D‐printing strategy is introduced to achieve programmable de‐icing devices. By aligning gold–magnetite nanofillers within a photosensitive resin, the printed structures exhibit dual magnetic and plasmonic functionalities, enabling precise spatio‐temporal ice removal through thermoplasmonic effects.
Amélie Pérot   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy