Results 81 to 90 of about 218,297 (244)

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Highway geometric design using Bézier curve approximation

Journal of Innovative Transportation, 2020
Traditional highway design procedure is a trial and error process where the system manager spends a lot of time. To improve this manual process, a new method to design highways is investigated. A mathematical function called Bézier Curve is used. Highway
Mehmet Saltan, Ekinhan Erişkin, Serdal Terzi, Şebnem Karahançer   +3 more
doaj  

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

PBF‐LB/M of Ti‐6Al‐4V: High‐Pressure Solution Treatment and Aging for Applications in a Sustainable Aerospace

Advanced Engineering Materials, EarlyView.
Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann, Andre Danzig, Freerk Syassen, Rainer Fechte‐Heinen, Anastasiya Toenjes   +4 more
wiley   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

A Thermodynamic 3D Model for the Simulation of Diffusion‐Controlled Alloying Processes in Heterogeneous Material Structures

Advanced Engineering Materials, EarlyView.
A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer, Leonhard Holländer, André Langohr, Hans Jürgen Maier   +3 more
wiley   +1 more source

Influence of Sample Preparation and Processing Procedures on the Thermal Diffusivity of MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan, Rhena Wulf, Till M. J. Stadtmüller, Christos G. Aneziris, Tobias M. Fieback   +4 more
wiley   +1 more source

Vehicle operating speeds in southwestern Colombia: An important database for the future implementation of optimization models for geometric design of roads in mountain topography. [PDF]

Data Brief, 2020
Wilches FJ, Burbano JLA, Sierra EEC.
europepmc   +1 more source