Results 91 to 100 of about 4,807,848 (253)
, 1995 Uma alta rugosidade superficial e adequado diâmetro médio geométrico (DMG) dos torrões do solo são propri- edades de superfície desejáveis para o controle da erosão hídrica. Por outro lado, ainda é pouco conhecido o efeito da opera- ção de semeadura sobre estas propriedades.
BERTOL, OROMAR JOÃO +1 more
openaire +1 more source
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
Impact of hammer mill on corn crushing size and size distribution
Siliao yanjiu, 2022 The experiment aimed at the hammer mill, which is widely used in feed enterprises at present, to carry out the research on corn crushing technology. The BT-2900 dynamic particle image analyzer was used to determine and analyze the particle size of Yunnan
HUANG Wei +5 more
doaj
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
Ciência Florestal, 2018 Differences in seed morphology may indicate variability within and among plant populations. Seeds of Annona reticulata Vell., Annonaceae were biometrically characterized, came from the Rio Brilhante region, Mato Grosso do Sul state, in a fragmented area ...
Montcharles da Silva Pontes +3 more
doaj +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
, 2015 In a study of traffic, the labelling problems in graph theory can be used by considering the crowd at every junction as the weights of a vertex and expected average traffic in each street as the weight of the corresponding edge. If we assume the expected
Baskar, A. D., Arockiaraj, S.
core +1 more source
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Geometry quantification for growth assessment of abdominal aortic aneurysms under surveillance
Scientific ReportsAbdominal Aortic Aneurysms (AAAs) are localized expansions of the abdominal aorta with complex growth patterns, which offer challenges in accurately characterizing aneurysm growth and morphological evolution using traditional maximum diameter $$(D_{max})$
Juan C. Restrepo +8 more
doaj +1 more source
Cogent Food & Agriculture, 2017 Physical properties of agricultural products are the most important parameters to determine the optimum design of grading, conveying, processing, and packaging systems.
F.U. Asoiro +3 more
doaj +1 more source