Results 141 to 150 of about 3,811,747 (317)

Geometric Algebra Jordan–Wigner Transformation for Quantum Simulation

Entropy
Quantum simulation qubit models of electronic Hamiltonians rely on specific transformations in order to take into account the fermionic permutation properties of electrons. These transformations (principally the Jordan–Wigner transformation (JWT) and the
Grégoire Veyrac, Zeno Toffano
doaj   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio

Advanced Engineering Materials, EarlyView.
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov, Matheus Roberto Bellé, Anton Yehorov, Julia Richter, Olena Volkova   +4 more
wiley   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

Advanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu, Timon Steinhoff, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Christian Klose, Ludger Overmeyer, Hans‐Jürgen Maier, Nina Merkert   +8 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source