Results 61 to 70 of about 12,318 (243)

Experimental Demonstration of Sequential Operation Approach for a Three-Sided Pyramid Wavefront Sensor

IEEE Photonics Journal, 2016
We describe a sequential operation approach for a three-sided pyramid wavefront sensor (PWFS) based on a micromirror array with hexagonal geometry. The geometrical optics analysis and numerical simulations show that a linear relationship exists between ...
Lu Chen, Jianli Wang, Kainan Yao, Xinyue Liu, Xudong Lin, Liang Wang, Minghao Wang   +6 more
doaj   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

METHOD OF MEASUREMENT OF THE PRESSURE IN HYDRAULIC AND PNEUMATIC SYSTEMS WITH LASER BEAM APPLICATION [PDF]

Scientific Journal of Silesian University of Technology. Series Transport, 2014
In the paper, non-contact method of measurement of the pressure with laser beam application is described. Actual solution associated with the topic is shown.
Marek SIKOŃ, Michał PRĄCIK
doaj  

The Design of Media on Two-Lens System Experiment (MTLSE) for Pre-service Physics Teachers

JPPPF: Jurnal Penelitian & Pengembangan Pendidikan Fisika, 2018
This article is a part of the research in designing a model of the geometrical-optics game on optics' courses for pre-service physics teachers (PPTs). This article describes the preliminary form of product, the result of validation, and PPTs’ responses
Saprudin Saprudin, Liliasari Liliasari, Ary Setijadi Prihatmanto, Andhy Setiawan   +3 more
doaj   +1 more source

Faster and More Accurate Geometrical-Optics Optical Force Calculation Using Neural Networks. [PDF]

ACS Photonics, 2023
Bronte Ciriza D, Magazzù A, Callegari A, Barbosa G, Neves AAR, Iatì MA, Volpe G, Maragò OM.   +7 more
europepmc   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Bimetallic (NiFe) and Trimetallic (NiFeCr) Nanoalloys from Metal Oxides Using a Microwave Hydrogen Plasma

Advanced Engineering Materials, EarlyView.
Bimetallic (NiFe) and trimetallic (NiFeCr) nanoalloys (NAs) are synthesized using corresponding oxide mixtures using microwave hydrogen plasma within a few milliseconds. The process simultaneously 1) reduces metal oxides to metals; 2) downsizes the particles from micrometers to nanometers; and 3) blends the metals to form NAs.
Sachin Kumar, Mohammad Kazemi, Zichang Xiong, Thomas Cameron, Julian Held, Uwe Kortshagen   +5 more
wiley   +1 more source

Sustainable Synthesis of Bio‐Based Magnetic and Conductive Wood for Electromagnetic Interference Shielding Applications

Advanced Engineering Materials, EarlyView.
A wood‐based magnetic and conductive material called Magwood (MW), capable of blocking almost 99.99% of electromagnetic waves (in the X‐band frequency range), is synthesized using a simple, solvent‐free process. MW is lightweight, resists water, and is flame‐retardant, making it a promising alternative for shielding electronics. The rapid proliferation
Akash Madhav Gondaliya, Majed Amini, Mohammad Arjmand, Earl Johan Foster   +3 more
wiley   +1 more source