Results 111 to 120 of about 4,092,683 (376)

A Case‐Based Reasoning Approach to Model Manufacturing Constraints for Impact Extrusion

open access: yesAdvanced Engineering Materials, EarlyView.
A hybrid modeling approach is presented that combines constraint‐based process modeling and case‐based reasoning. The model formalizes manufacturing constraints and integrates simulation data to model complex manufacturing processes. The approach supports manufacturability analysis during product design through an adaptive modeling environment.
Kevin Herrmann   +5 more
wiley   +1 more source

Mechanisms of Increasing Weld Depth during Temporal Power Modulation in High‐Power Laser Beam Welding

open access: yesAdvanced Engineering Materials, EarlyView.
Temporal power modulation increases weld depth in high‐power laser beam welding of dissimilar round bars by nearly 20% compared to same average continuously welded welding power. The mechanism of action also applies to sheet welding and depends on the inertia of keyhole depth for the modulated laser beam power.
Jan Grajczak   +7 more
wiley   +1 more source

Anomaly Detection Method for Hybrid Workpieces Using Dynamic Time Warping

open access: yesAdvanced Engineering Materials, EarlyView.
Monitoring of hybrid workpieces: when machining hybrid workpieces, unavoidable axial deviations of the material transition zone cause temporal shifts in the process force signals. A new anomaly detection method based on dynamic time warping is proposed to detect material defects.
Berend Denkena   +3 more
wiley   +1 more source

Simulation of Inhomogeneous Refractive Index Fields Induced by Hot Tailored Forming Components

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents a simulation model for simulating inhomogeneous refractive index fields (IRIF) in hot‐forged components, accounting for thermal influences and complex geometries. Through this simulation, a priori knowledge about the propagation of the IRIF can be obtained, allowing for the positioning of the component or an optical measurement ...
Pascal Kern   +3 more
wiley   +1 more source

Intermetallic Compound Layer Morphology and Distribution in Friction‐Welded Steel–Aluminum Components

open access: yesAdvanced Engineering Materials, EarlyView.
In this study, how friction‐welding parameters (rotational speed, etc.) affect the morphology, distribution, and local thickness of the intermetallic compound layer (IMC‐layer) in friction‐welded steel‐aluminum hybrid components is investigated. In the results, it is shown that lower speeds (700 rpm) lead to a more uniform, thinner IMC‐layer (<0.5 μm),
Christoph Kahra   +6 more
wiley   +1 more source

Non‐Destructive and Mechanical Characterization of the Bond Quality of Co‐Extruded Titanium‐Aluminum Profiles

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates the bond quality of co‐extruded aluminum–titanium hybrid profiles, focusing on the lateral angular co‐extrusion (LACE) process. It examines how heat treatments (HT) affect intermetallic phase formation, bond strength, and material properties.
Norman Mohnfeld   +9 more
wiley   +1 more source

Geometry and categorification

open access: yes, 2016
We describe a number of geometric contexts where categorification appears naturally: coherent sheaves, constructible sheaves and sheaves of modules over quantizations.
Webster, Ben
core  

Comparative Wear and Friction Analysis of Sliding Surface Materials for Hydrostatic Bearing under Oil Supply Failure Conditions

open access: yesAdvanced Engineering Materials, EarlyView.
Hydrostatic bearings excel in high‐precision applications, but their performance hinges on a continuous external supply. This study evaluates various material combinations for sliding surfaces to mitigate damage during supply failures or misalignment and to discover the most effective materials identified for enhancing the reliability and efficiency of
Michal Michalec   +6 more
wiley   +1 more source

Home - About - Disclaimer - Privacy