Results 271 to 280 of about 1,899,512 (381)

Development and Validation of a One‐Dimensional Finite Difference Simulation Scheme for Polymer Laser Powder Bed Fusion with Application to the Effect of the Inter Layer Time

Advanced Engineering Materials, EarlyView.
The study presents an efficient simulation approach for the polymer laser powder bed fusion process polymers process, validated with polyamide 12, polyamide 6, and polyetherketoneketone. It shows that inter layer time affects part density, with 90s yielding dense parts.
Claas Bierwisch, Bastien Dietemann, Moritz Grünewald, Christian Schlör, Johannes Rudloff   +4 more
wiley   +1 more source

Can Smart Alloy Material Improve the Biomechanical Behavior of Prostheses Used in the Human Trachea? A Fluid-Structure Interaction Approach. [PDF]

Biomed Eng Comput Biol
Mortazavy Beni H.
europepmc   +1 more source

Wedge Geometry for Ultrasonic Delay Lines

, 1954
H. J. McSkimin
openalex   +1 more source

Development of Ternary Magnesium Alloys for Laser Powder Bed Fusion: Optimizing Oxide Layer Thickness

Advanced Engineering Materials, EarlyView.
Additive manufacturing of magnesium alloys by laser is difficult because the melting point of the oxide layer is much higher than the evaporation temperature of the metal underneath. Making the oxide layer thinner can solve this problem. Alloying magnesium with strontium makes the oxide layer thinner, especially at 0.5 wt%.
Elmar Jonas Breitbach, Stefan Julmi, Sabine Behrens, Tatiana Blank, Arvid Abel, Nicole Emminghaus, Ludger Overmeyer, Christian Klose, Hans Jürgen Maier   +8 more
wiley   +1 more source

Topology-inclusive aerodynamic shape optimisation using a cellular automata parameterisation. [PDF]

Struct Multidiscipl Optim
Wood MJ, Rendall TCS, Allen CB, Kedward LJ, Taylor NJ, Fincham J, Leppard NE.   +6 more
europepmc   +1 more source

A Case‐Based Reasoning Approach to Model Manufacturing Constraints for Impact Extrusion

Advanced Engineering Materials, EarlyView.
A hybrid modeling approach is presented that combines constraint‐based process modeling and case‐based reasoning. The model formalizes manufacturing constraints and integrates simulation data to model complex manufacturing processes. The approach supports manufacturability analysis during product design through an adaptive modeling environment.
Kevin Herrmann, Eduard Ortlieb, Hendrik Wester, Paul Christoph Gembarski, Bernd‐Arno Behrens, Roland Lachmayer   +5 more
wiley   +1 more source

Relationship between interaction geometry and cooperativity measured in H-bonded networks of hydroxyl groups. [PDF]

Chem Sci
Trevisan L, Bond AD, Hunter CA.
europepmc   +1 more source

Mechanisms of Increasing Weld Depth during Temporal Power Modulation in High‐Power Laser Beam Welding

Advanced Engineering Materials, EarlyView.
Temporal power modulation increases weld depth in high‐power laser beam welding of dissimilar round bars by nearly 20% compared to same average continuously welded welding power. The mechanism of action also applies to sheet welding and depends on the inertia of keyhole depth for the modulated laser beam power.
Jan Grajczak, David Reynders, Christian Nowroth, Jens Twiefel, Jörg Wallaschek, Sarah Nothdurft, Jörg Hermsdorf, Stefan Kaierle   +7 more
wiley   +1 more source

Influence of Measurement Geometry and Blank on Absolute Measurements of Photoluminescence Quantum Yields of Scattering Luminescent Films. [PDF]

Anal Chem
Frenzel F, Fiedler S, Bardan A, Güttler A, Würth C, Resch-Genger U.   +5 more
europepmc   +1 more source

Anomaly Detection Method for Hybrid Workpieces Using Dynamic Time Warping

Advanced Engineering Materials, EarlyView.
Monitoring of hybrid workpieces: when machining hybrid workpieces, unavoidable axial deviations of the material transition zone cause temporal shifts in the process force signals. A new anomaly detection method based on dynamic time warping is proposed to detect material defects.
Berend Denkena, Benjamin Bergmann, Heinrich Klemme, Miriam Handrup   +3 more
wiley   +1 more source