Results 51 to 60 of about 831 (157)

High Temperature Oxidation Behavior of GH4169 Nickel Base Superalloy Under Different Grindings for Internal Combustion Engine [PDF]

Cailiao Baohu, 2021
In order to improve the high temperature oxidation resistance of GH4169 nickel base superalloy for internal combustion engine, the GH4169 nickel base superalloy’s surface was polished with different types of sandpaper, and then the oxidation resistance ...
LIU Yi-fu, ZHENG Jian-xin, SUN Rui-xia
doaj   +1 more source

Effect of Notch Structure and Notch Bottom Diameter on the Tensile Load of a Certain GH4169 Notch Bolt for a Device for Longitudinal Separation of Fairing

Metals, 2022
The effect of the notch structure and bottom diameter of a GH4169 notch bolt for an explosive separation device used for longitudinal separation of the fairing, and GH4169 strength range on the tensile load was studied by combing simulations with tests ...
Xiaoliang Wang, Yunxian Cui, Tiebing Yuan, Xiaowei Wang, Zenghui Jiang   +4 more
doaj   +1 more source

Effect of brazing temperature on microstructure and mechanical properties of GH4169/AgCuTi+W/Si3N4 joint

Journal of Aeronautical Materials, 2022
Nickel-based superalloy (GH4169) and Si3N4 ceramics were connected by AgCuTi composite active filler and high purity W foil which acts as interlayer. The effects of temperature on the microstructure evolution and mechanical properties of GH4169/ Si3N4 ...
XUE Yang, ZHU Dongdong, TAO Feng, DONG Duo, WANG Xiaohong, MA Tengfei   +5 more
doaj   +1 more source

Effects of hot isostatic pressing and heat treatment process on microstructure and tensile properties of selective laser melting manufactured GH4169 alloy

Cailiao gongcheng, 2020
GH4169 alloys were manufactured by selective laser melting (SLM). The microstructure evolution and tensile properties of GH4169 alloys during hot isostatic pressing(HIP) and heat treatment(HT) process were analyzed by OM,SEM,EBSD and TEM.
SHI Lei, LEI Li-ming, WANG Wei, FU Xin, ZHANG Guang-ping   +4 more
doaj   +1 more source

Investigating the Contact Responses of the Roller Cavity Surfaces in the Compressor Blade Rolling Process

Advances in Materials Science and Engineering, Volume 2020, Issue 1, 2020., 2020
The investigation of the contact responses is the key for evaluating the local wear of dies in the plastic forming process. This paper investigated the contact load distributions and evolutions of the roller cavities in the compressor blade rolling process by the FEM.
Qichao Jin, Wenhu Wang, Ruisong Jiang, Guian Qian   +3 more
wiley   +1 more source

Study on Friction and Wear Behavior of Inconel 625 Superalloy during Hot Extrusion

Advances in Materials Science and Engineering, Volume 2020, Issue 1, 2020., 2020
Friction during the hot extrusion of Inconel 625 superalloy tubes causes severe wear of the mold and plays a decisive role in the quality of the workpieces. In this paper, a ball‐to‐disk method was utilized to investigate the tribological behavior of Inconel 625 using two different tribological pairs, i.e., GCr15 and Si3N4, at room and elevated ...
Yanjiang Wang, Sixiang Zhao, Zhi Jia, Jinjin Ji, Dexue Liu, Tingbiao Guo, Yutian Ding, Georgios Maliaris   +7 more
wiley   +1 more source

Investigations on correlation between grain size and stress rupture property of GH4169 alloy

Journal of Aeronautical Materials, 2020
Taking GH4169 alloy large-size bar as research object, combined with the manufacturing process of the bar, the stress rupture properties of the specimens with different grain sizes were analyzed by means of OM, FE-SEM, EBSD and TEM. The results show that
WEI Kang, ZHANG Yong, WANG Tao, LI Zhao, WAN Zhipeng   +4 more
doaj   +1 more source

Wear behavior of Ag implantation GH4169 alloy by ion beam assisted bombardment

, 2018
The wear behavior of Ag implantation GH4169 alloy by ion beam assisted bombardment was measured under lower applied load and sliding speed. The wear rate of GH4169 alloy decreased from 2.58 × 10−4 mm3·m−1 to 6.25 ×10−5 mm3·m−1 after Ag implantation. The
Lingping Zhou, Wulin Yang, Deyi Li, Meng Xu, Jiajun Zhu, Licai Fu   +5 more
core   +1 more source

Superior Abrasibility of YSZ(ESP)/BN@ZrO2‐Polyester Composite Sealing Coating Reinforcing With Hybrid Micron/Nanometer Multiscaled Pore Structure

Rare Metals, Volume 45, Issue 5, May 2026.
ABSTRACT Composite materials hold significant potential for abrasive sealing, yet composite materials used for abrasive sealing fall short in service durability under extreme environments. Here, a controllable strategy for adjusting pore structure is proposed, aiming to design a YSZ(ESP)/BN@ZrO2‐polyester coating with hybrid micron/nanometer ...
Shuang Yu, Shuqi Wang, Yaming Wang, Jiao Han, Zhiyun Ye, Kai Lv, Yongchun Zou, Guoliang Chen, Jiahu Ouyang   +8 more
wiley   +1 more source

Effect of co-strengthening of laser shock peening and mechanical shot peening on surface integrity and vibration fatigue properties of GH4169 alloy

Cailiao gongcheng
Vibration fatigue specimens are designed based on the load-cases of compressor blades， and performed by mechanical shot peening， laser shock peening， and co-strengthening of laser shock peening followed by mechanical shot peening respectively.
TIAN Kai, WU Xiaoyan, LI Wei, XIE Chao, LUO Xuekun, WANG Xin   +5 more
doaj   +1 more source