Results 101 to 110 of about 3,791 (280)
Effect and Mechanism of the Surface Treatment and Gradation Filling of AlN on the Performance of Insulation Layer of Copper Clad Laminate [PDF]
Journal of Inorganic Materials, 2021 Wan JIANG +4 more
openaire +1 more source
Sliding contact at plastically graded surfaces and applications to surface design [PDF]
, 2007 Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Civil and Environmental Engineering, 2007.This electronic version was submitted by the student author.
Prasad, Anamika, 1979-
core
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
, 2008 The objective of this study is to investigate a particular type of crack problem in a layered structure consisting of a substrate, a bond coat, and an orthotropic functionally graded material coating. There is an internal crack in the orthotropic coating
YILDIRIM, BORA +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Görüntü yöntemlerinin beton mikro yapısının ve çelik birleşimlerin deformasyon davranışlarının belirlenmesinde uygulanması [PDF]
, 2007 TÜBİTAK MAG Proje01.07.2007In this project, two different studies were conducted using digital imaging techniques. In the first phase, relationships between aggregate shape parameters and concrete strength were investigated. The relationships were sought
Güler, Murat +2 more
core
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Grinding surface of variable curvature of the abrasive discs Trizact™
, 2015 W artykule przedstawiono możliwości wykorzystania innowacyjnej głowicy szlifiersko-polerskiej do obróbki powierzchni o zmiennej krzywiźnie. Powierzchnie kształtowe obrabiane były na 3-osiowym centrum frezarskim HAAS frezem kulowym, a następnie szlifowane
Plichta, J., Baran, J.
core