Results 191 to 200 of about 3,741,721 (286)

Current Tracking Adaptive Control of Brushless DC Motors

International Journal of Adaptive Control and Signal Processing, EarlyView.
In this paper, the current tracking for Brushless Direct Current motors is approached considering uncertainty in the parameters of the motor's model. An adaptive control scheme to compensate electrical parameters uncertainty is proposed without requiring any knowledge of the mechanical parameters.
Fernanda Ramos‐García, Axel Coronado‐Andrade, Gerardo Espinosa‐Pérez, Luis Alvarez‐Icaza   +3 more
wiley   +1 more source

Optimization and validation of traction performance for an eight-axle heavy-haul locomotive during gradient starting. [PDF]

Sci Rep
Liu Y, Wu X, Ma P, Yuan X.
europepmc   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Optimization of the cut configuration for skin grafts. [PDF]

Biomech Model Mechanobiol
Harbrecht H, Karnaev V.
europepmc   +1 more source

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Pore-Scale Investigations into Gradient Carbon Microstructures for Enhanced Mass Transport in PEM Fuel Cell Catalyst Layers. [PDF]

Nanomaterials (Basel)
Zhang C, Li L, Wang H, Yang G, Huang N, Sheng Z.   +5 more
europepmc   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Self- and Goal-Directed Valsalva Maneuver vs Exercise in Eliciting Left Ventricular Outflow Tract Obstruction. [PDF]

JACC Adv
Bavishi A, Fritzlen J, Nazif K, Soutar M, Kurnides M, Speer H, Oyarce G, Richards K, Flahive C, Martinez MW.   +9 more
europepmc   +1 more source

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Experimental investigation of mechanical properties in cryogenically damaged shale. [PDF]

Sci Rep
Zheng X, Zhang G, Wang D, Yang F, Lu M, Song L, Zhou D.   +6 more
europepmc   +1 more source