Results 71 to 80 of about 6,034 (257)
Loss of Height Pressure in a Layer of Granular Materials
The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2019 During the air blown in the furnace, from the vents to the loading mouth, the gases lost from the initial pressure depend on several factors, such as the care and the granulation mixed with ores and coke from the layers of care.
Adrian VASILIU
doaj +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
A Langevin Description for Driven Granular Gases [PDF]
Mathematical Modelling of Natural Phenomena, 2011 Ministerio de Educación y Ciencia FIS2008 ...
Maynar Blanco, Pablo +1 more
openaire +3 more sources
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Temperature of a granular gas with regard to the stochastic nature of particle interactions
New Journal of Physics, 2013 The decay of temperature of a force-free granular gas in the homogeneous cooling state depends on the specific model for particle interaction. For the case of rough spheres, in recent experimental and theoretical work, the coefficient of restitution was ...
Nina Gunkelmann +2 more
doaj +1 more source
Rheology of dilute cohesive granular gases [PDF]
Physical Review E, 2018 Rheology of a dilute cohesive granular gas is theoretically and numerically studied. The flow curve between the shear viscosity and the shear rate is derived from the inelastic Boltzmann equation for particles having square-well potentials in a simple shear flow. It is found that (i) the stable uniformly sheared state only exists above a critical shear
Takada, Satoshi, Hayakawa, Hisao
openaire +3 more sources
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Dissipative lateral walls are sufficient to trigger convection in vibrated granular gases
EPJ Web of Conferences, 2017 Buoyancy-driven (thermal) convection in dilute granular media, fluidized by a vibrating base, is known to appear without the need of lateral boundaries in a restricted region of parameters (inelasticity, gravity, intensity of energy injection).
Pontuale Giorgio +3 more
doaj +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source