Results 211 to 220 of about 32,486 (279)

Een gravure van Israhel van Meckenem: de Kerkgangers

The Rijksmuseum Bulletin, 1990
J. P. Filedt Kok
doaj   +1 more source

Towards practical point-of-care quick, ubiquitous, integrated, cost-efficient molecular diagnostic Kit (QUICK) PCR for future pandemic response. [PDF]

Microsyst Nanoeng
Kim S, Shrestha K, Cho G.
europepmc   +1 more source

Effect of build orientation on the fabrication trueness of additively manufactured implant‐supported complete arch interim fixed prostheses

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate how build orientation affects the fabrication trueness of additively manufactured implant‐supported complete arch prostheses by comparing them to subtractively manufactured high‐impact polymer‐based prostheses. Materials and Methods An edentulous maxillary model with four implants at canine and first molar regions ...
Amir H. Nejat, Mehmet Esad Güven, Gülce Çakmak, Burak Yilmaz, Mustafa Borga Donmez   +4 more
wiley   +1 more source

Flexible perovskite solar cells: advancements in materials, fabrication techniques, and future prospects. [PDF]

Nano Converg
Nawaz MH, Mai TH, Seok SII, Chuang FC, Pham PV, Park NG.   +5 more
europepmc   +1 more source

Wettability of saliva substitutes across various denture base fabrication techniques

Journal of Prosthodontics, EarlyView.
Abstract Purpose The present study evaluated the contact angles (CAs) of four denture base materials subjected to different surface treatments using deionized water and saliva substitutes. Material and Methods A total of 32 rectangular specimens were manufactured using four different denture base materials: heat‐cured compression molded Lucitone 199 (C)
Paul Mikhail, Igor Pesun, Francisco Azpiazu‐Flores, Rodrigo França   +3 more
wiley   +1 more source

Effects of autoclave sterilization on the dimensional stability of implant surgical guides: A 3D in vitro analysis

Journal of Prosthodontics, EarlyView.
Abstract Purpose Surgical guides are medical devices used in static implant surgery to replicate the prosthetic and surgical implant position planned with computer‐assisted software before surgery. Their use reduces invasiveness and improves safety and outcomes of implant surgery, provided that their accuracy is ensured from design to manufacturing and
Lucio Lo Russo, Pierluigi Mariani, Carlo Ercoli, Giusy Caprio, Ji‐Man Park, Luigi Laino, Fariba Esperouz   +6 more
wiley   +1 more source

Marginal gap of printed, milled, and heat‐pressed two‐piece polyetheretherketone abutments before and after thermal cycling, and their pull‐off bond strength after thermal cycling

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the marginal gap of two‐piece polyetheretherketone (PEEK) abutments fabricated with different methods, before and after thermal cycling, while also focusing on their pull‐off bond strength. Materials and Methods A two‐piece abutment was virtually designed after digitizing a titanium‐base (Ti‐base) abutment.
Almira Ada Diken Türksayar, Burcu Kanpalta, Naime Bilinç Bulucu, Sandra Schulnig, Sebastian Spintzyk, Münir Demirel, Mustafa Borga Donmez   +6 more
wiley   +1 more source

Porous Polymeric Nanofilms for Recreating the Basement Membrane in an Endothelial Barrier-on-Chip. [PDF]

ACS Appl Mater Interfaces
Mancinelli E, Zushi N, Takuma M, Cheng Chau CC, Parpas G, Fujie T, Pensabene V.   +6 more
europepmc   +1 more source

Workflow to facilitate complete denture scanning with an intraoral scanner: A technique report

Journal of Prosthodontics, EarlyView.
Abstract Scanning a denture with an intraoral scanner is typically more challenging than scanning a dentate arch. This article describes a novel technique for digitally duplicating a complete denture. The workflow involves scanning an existing denture using an intraoral scanner with the addition of specific markers and subsequently constructing a ...
Jiayi Yu, Jiayi Lu, Berna Saglik, Junying Li   +3 more
wiley   +1 more source

Fracture load and retention of milled interim implant restorations fabricated on three types of abutments and two implant diameters: An in vitro study

Journal of Prosthodontics, EarlyView.
ABSTRACT Purpose To evaluate the fracture load and retention of subtractively manufactured interim restorations for single‐unit implants of two diameters, using three interim abutment types: stock abutments, titanium base (Ti‐base) abutments, and pre‐milled polymethyl methacrylate (PMMA) abutments.
Dong‐Hun Lee, Carme Riera, Qiucen Wan, Nareudee Limpuangthip, Jae‐Hyun Lee, Sang J. Lee   +5 more
wiley   +1 more source