Results 31 to 40 of about 32,486 (279)
Positive‐Tone Nanolithography of Antimony Trisulfide with Femtosecond Laser Wet‐Etching
Advanced Functional Materials, EarlyView.A butyldithiocarbamic acid (BDCA) etchant is used to fabricate various micro‐ and nanoscale structures on amorphous antimony trisulfide (a‐Sb2S3) thin film via femtosecond laser etching. Numerical analysis and experimental results elucidate the patterning mechanism on gold (reflective) and quartz (transmissive) substrates.
Abhrodeep Dey +12 more
wiley +1 more source
Gravure-Printed Anodes Based on Hard Carbon for Sodium-Ion Batteries
BatteriesPrinted batteries are increasingly being investigated for feeding small, wearable devices more and more involved in our daily lives, promoting the study of printing technologies.
Maria Montanino +3 more
doaj +1 more source
Use of the Vandercook Proof Press to Predict Rotogravure Print Quality [PDF]
, 1970 The object of this thesis is to investigate a new idea in predicting printability for rotogravure printing. Present proof presses in the gravure industry are clumsy, expensive, and in most cases, impractical for regular use.
Phee, Patrick
core +1 more source
Meta‐Rod Mechanical Metamaterials With Programmable Reconfiguration
Advanced Functional Materials, EarlyView.Existing mechanical metamaterials achieve programmable large deformations in planar square or cubic configurations, restricted by required complex boundary conditions. This research proposes a 1D metamaterial, Meta‐rod, with linear, bending, twisting, area, and volume deformation modes.
Atharva Pande, Lyes Kadem, Hang Xu
wiley +1 more source
Gourd‐Inspired Design of Unit Cell with Multiple Gradients for Physiological‐Range Pressure Sensing
Advanced Functional Materials, EarlyView.Gourd‐shaped micro‐dome arrays with coordinated modulus, conductivity, and geometric gradients co‐optimize sensitivity and linearity in piezoresistive tactile sensors. Under pressure, a solid upper dome embeds into a porous lower dome, triggering rapid contact‐area growth and series‐to‐parallel conduction, enabling unsaturated, intensity‐resolved ...
Jiayi Xu +6 more
wiley +1 more source
LFP-Based Gravure Printed Cathodes for Lithium-Ion Printed Batteries
Membranes, 2019 Printed batteries have undergone increased investigation in recent years because of the growing daily use of small electronic devices. With this in mind, industrial gravure printing has emerged as a suitable production technology due to its high speed ...
Maria Montanino +3 more
doaj +1 more source
Advanced Electronic Materials, 2020 A limitless‐length flexible active‐matrix implies that virtually any surface can be rendered into an interactive medium when laminated with electrophoretic or organic light‐emitting diode sheets.
Junfeng Sun +15 more
doaj +1 more source
Classification and analyses of of coating flows [PDF]
, 1994 YesA classification of coating flows is presented to facilitate a fundamental approach to their study. Four categories are observed: free, metered, transfer and gravure coating flows.
Benkreira +37 more
core +1 more source
Advanced Functional Materials, EarlyView.Tailored thermo‐mechanical properties of shape memory polymer composites enable large reversible deformation as well as high actuation speed. Moreover, a structural design with curvature in the transverse direction achieves sub‐second actuation on heating and a larger recovery ratio on cooling. Finally, these newly developed smart two‐way actuators can
Dajeong Kang +6 more
wiley +1 more source
Development of a novel wrinkle-structure based SERS substrate for drug detection applications
Sensing and Bio-Sensing Research, 2019 A novel wrinkle-structure based surface enhanced Raman spectroscopy (SERS) substrate was successfully developed for the detection of drugs such as cocaine.
Dinesh Maddipatla +7 more
doaj +1 more source