Results 181 to 190 of about 856,223 (304)

Building a Greener Future: A Techno‐Economic Assessment of Renewable Configurations for Energy Independence and the Net‐Zero Transitions in a Community Microgrid [PDF]

Muhammad Adnan Khan, Abdul Haseeb, Muhammad Mansoor Ashraf, Muhammad Waseem, Muhammad Ali MUGHAL, Fabiano Pallonetto   +5 more
openalex   +1 more source

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Influence of B'-site vacancy on hydrogen storage, structural, elastic, thermodynamic and optoelectronic attributes of potassium based double perovskite K₂LiAlH₆hydride for green energy applications. [PDF]

Sci Rep
Murtaza H, Habib MA, Ain Q, Kumar A, Munir J, Ibrahim ABM, Oza AD, Al-Salimi MSS.   +7 more
europepmc   +1 more source

How green-technology, energy-transition and resource rents influence load capacity factor in South Africa [PDF]

Emmanuel Uche, Nicholas Ngepah
openalex   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Green software development using carbon-aware scheduling techniques and energy efficiency metrics throughout the SDLC

Piatrouski, Mikita
openalex   +1 more source

Efficient Process Development for Laser Powder Bed Fusion of a Soft‐Magnetic Metallic Glass Composite

Advanced Engineering Materials, EarlyView.
Iron‐based metallic glass alloys exhibit excellent soft‐magnetic properties, and unprecedented geometrical freedom in the design of soft‐magnetic metallic glass components is made possible by additive manufacturing. An efficient workflow for developing parameters for laser‐based powder bed fusion of a Fe‐based metallic glass alloy is presented along ...
Julia Löfstrand, Priyanka Saha, Vidhiaza Leviandhika, Urban Wiklund, Alexander Elsen, Carolin Zintel, Lena Thorsson, Petra E. Jönsson   +7 more
wiley   +1 more source

Striking a balance: Europe's green energy ambitions and the environmental impact of lithium. [PDF]

Lancet Reg Health Eur
The Lancet Regional Health-Europe.
europepmc   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Insights from the nexus between economic growth and green energy. [PDF]

Heliyon
Sichigea M, Puiu S, Circiumaru D, Carstina S.   +3 more
europepmc   +1 more source