Results 71 to 80 of about 685,333 (350)

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Enhanced dynamic support strategies of grid-forming-PMSG based on DC-voltagesynchronization: Frequency and Q support perspective

International Journal of Electrical Power & Energy Systems
The DC-Voltage Synchronization based Grid-Forming PMSG has voltage source characteristics, e.g. frequency and reactive power support function, however, the support capability is limited, and the regulation potential is not fully utilized.
Dejian Yang, Tongyu Hu, Taiying Zheng, Minhui Qian, Chaoquan Li, Zhijie Cao, Gangui Yan   +6 more
doaj   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

AC-Side Impedance-Based Stability Assessment in Grid-Forming Modular Multilevel Converters

IEEE Access
Grid-forming converters can emulate the behavior of a synchronous generator through frequency droop control. The stability of grid-forming modular multilevel converters can be studied via the impedance-based stability criterion. This paper presents an ac-
Mehrdad Nahalparvari, Mohsen Asoodar, Staffan Norrga, Hans-Peter Nee   +3 more
doaj   +1 more source

The Numerical Simulation of Radiative Shocks I: The elimination of numerical shock instabilities using a localized oscillation filter [PDF]

, 2002
We address a numerical instability that arises in the directionally split computation of hydrodynamic flows when shock fronts are parallel to a grid plane.
Bicknell, G. V., Bisset, D. K., Sutherland, R. S.   +2 more
core   +2 more sources

Grid-forming VSM control for black-start applications with experimental PHiL validation [PDF]

, 2023
Abdulrahman Alassi, Zhiwang Feng, Khaled H. Ahmed, Mazheruddin Syed, Agustí Egea‐Àlvarez, Colin Foote   +5 more
openalex   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Immunity of Grid-Forming Control Without Energy Storage to Transient Changes of Grid Frequency and Phase

IEEE Open Journal of the Industrial Electronics Society
European grid operators in ENTSO-E and others with a significant amount of inverter-based generation are experiencing a reduction in system inertia and short-circuit power.
Norbert R. Klaes, Jens Fortmann
doaj   +1 more source

ITERA: IDL Tool for Emission-line Ratio Analysis [PDF]

, 2001
We present a new software tool to enable astronomers to easily compare observations of emission line ratios with those determined by photoionization and shock models, ITERA, the IDL Tool for Emission-line Ratio Analysis.
I Porteous, M Crombrugghe De, R.A. Coles
core   +3 more sources

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source