Results 1 to 10 of about 23,542 (164)
Establishment and Verification of the Cutting Grinding Force Model for the Disc Wheel Based on Piezoelectric Sensors [PDF]
Sensors, 2019 In this paper, a new model of cutting grinding force for disc wheels is presented. Initially, it was proposed that the grinding cutting force was formed by the grinding force and cutting force in combination.
Jing Ni +4 more
doaj +2 more sources
A New Grinding Force Model for Micro Grinding RB-SiC Ceramic with Grinding Wheel Topography as an Input [PDF]
Micromachines, 2018 The ability to predict the grinding force for hard and brittle materials is important to optimize and control the grinding process. However, it is a difficult task to establish a comprehensive grinding force model that takes into account the brittle ...
Zhipeng Li +6 more
doaj +2 more sources
Experimental Investigation of Grinding Force and Material Removal Mechanism of Laser-Structured Zirconia Ceramics [PDF]
Micromachines, 2022 Zirconia is a high demanded structural ceramic with desirable mechanical, thermal, and chemical properties. Poor surface integrity and limited material removal rate caused by high cutting force and wheel wear are the main problems in ceramic grinding. In
Jingzhu Pang +3 more
doaj +2 more sources
Model for Predicting the Micro-Grinding Force of K9 Glass Based on Material Removal Mechanisms [PDF]
Micromachines, 2020 K9 optical glass has superb material properties used for various industrial applications. However, the high hardness and low fracture toughness greatly fluctuate the cutting force generated during the grinding process, which are the main factors ...
Hisham Manea +5 more
doaj +2 more sources
Jin'gangshi yu moliao moju gongcheng, 2022 In order to study the grinding force of diamond wheel in axial feed grinding of cemented carbide, the transformation models of horizontal grinding force, vertical grinding force, normal force and tangential force are established, the variation of ...
Xiaoke REN, Hui HUANG, Zhenfa SU
doaj +1 more source
Crystals, 2023 The grinding force is an important index during the grinding process, which affects the surface quality and other aspects after machining. However, the research on the grinding force of ceramic matrix composites assisted by two-dimensional ultrasonic ...
Yunguang Zhou +5 more
doaj +1 more source
Model construction and experimental research on end grinding force of SiCp/Al composites
Jin'gangshi yu moliao moju gongcheng, 2023 Aiming at the problem that precision and efficient end grinding is required for the two-phase 3D reconstruction of SiCp/Al grinding layer by layer, an analytical model of end grinding force of SiCp/Al is established based on the grinding force of SiCp/Al
Guixin CAO +3 more
doaj +1 more source
Measurements of Non-Grinding Forces and Power
International Journal of Automation Technology, 2021 Grinding forces and power are important parameters for evaluating grinding process performance, and they are typically measured in grinding experiments. Forces are typically measured using a load cell or a dynamometer, whereas power is measured using an electrical power sensor to monitor the power of the spindle motor.
Shi, Zhongde, Attia, Helmi
openaire +2 more sources
Forces and Specific Energy of Polyamide Grinding [PDF]
Materials, 2021 This work investigated the grinding process of reinforced and nonreinforced polyamide materials using an Al2O3 grinding wheel. Samples were ground using a custom-made setup of sensors to evaluate in-line temperature, forces, and power. The surface roughness and images were acquired to assess the quality of the final products. The novelty of the work is
Roberto Spina +3 more
openaire +2 more sources
Grinding Force in Grinding with a Single Grain
Journal of the Japan Society of Precision Engineering, 1971 In this report interference phenomenon between a grain groove and grinding force with the single grain passing through close the groove is researched theoretically and experiment-ally. Assuming that grinding force with a single grain consists of ploughing force and friction force, the factors which control grinding force may be approximately given with
Masaki MORI +2 more
openaire +3 more sources