Results 141 to 150 of about 702,143 (289)

Strong-Motion Data Processing and Product Generation System for Earthquake Early Warning Network

Applied System Innovation
For processing timeliness, standardizing formats, and reflecting the variety of massive strong motion observation data of the National Seismic Network Center, we developed a strong motion data processing system applicable to different types of strong ...
Yanqiong Liu, Liye Zou, Qi Zhang, Xumao Li   +3 more
doaj   +1 more source

Impact of Sustainable Binders Based on Lignin and Collagen on the Volume Stability and Mechanical Properties of MgO‐C Refractories with MgO‐C Recyclates

Advanced Engineering Materials, EarlyView.
Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller, Florian Kerber, Kirsten Moritz, Steffen Dudczig, Konstantin Kraushaar, Thomas Schemmel, Jana Hubálková, Patrick Gehre, Christos G. Aneziris   +8 more
wiley   +1 more source

Optimal Design and Seismic Performance of Base-Isolated Structures with Varying Heights Equipped with Tuned Inerter Dampers Subjected to Far-Fault and Near-Fault Ground Motions

Applied Sciences
This paper investigates the optimal design of base-isolated structures equipped with tuned inerter dampers (TIDs) subjected to various ground motions. The Clough–Penzien model is employed to simulate the power spectrum of three types of ground motions ...
Yingjie Kang, Zewen Zhang, Zeyu Zhang, Xinyu Zhang, Qingkuan Liu   +4 more
doaj   +1 more source

Dielectric Barrier Discharge Plasma Deoxidation of Natively Oxide Layer of Copper Powders in a Fluidized Bed

Advanced Engineering Materials, EarlyView.
This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang, Annett Wollmann, Thomas Gimpel, Alfred P. Weber   +3 more
wiley   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Parameter Variation in Planetary Ball Milling of Titanium Aluminide Powder in XHV‐Adequate Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann, Armin Piwek, Julius Peddinghaus, Kai Brunotte, Bernd-Arno Behrens   +4 more
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source