Results 141 to 150 of about 5,182,060 (233)

Non‐Additive Criteria Assessment in Sustainability Evaluation of High Entropy Alloys: A Toxicity‐Weighted Framework

Advanced Engineering Materials, EarlyView.
Sustainability assessment requires methodologies that appropriately distinguish between additive and non‐additive material properties. A toxicity‐weighted scoring system is developed and applied that accounts for the disproportionate influence of highly toxic constituents through nonlinear weighting functions, providing more realistic estimates than ...
Seth Mehalic, Oladele A. Ogunseitan, Julie M. Schoenung   +2 more
wiley   +1 more source

Controlling Grain Growth in Powder Bed Fusion of Yttria‐Stabilized Zirconia Using Femtosecond Lasers: Challenges and Methodological Insights

Advanced Engineering Materials, EarlyView.
Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn, Sarah Kaden, Andrea Barz, Daniel Störzner, Jens Bliedtner, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Simulation‐Based Analysis of Insert Pull‐Out in Nickel‐Polyurethane Hybrid Foams Using CT‐Derived Geometries

Advanced Engineering Materials, EarlyView.
CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz, Jonas Fell, Hendrik Jost, Stefan Diebels, Hans‐Georg Herrmann   +4 more
wiley   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Parametric estimation of clutter autocorrelation matrix for ground moving target indication

, 2020
In airborne radar systems with Ground Moving Target Indication (GMTI) mode, it is desired to detectthe presence of targets in the interference consisting of noise, ground clutter, and jamming signals.These interference components usually mask the target return signal, such that the detection requiressuppression of the interference signals.
openaire   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

Materials‐Driven Additive Manufacturing for Electrical Machines: Qualification‐Oriented Design Beyond Geometric Freedom

Advanced Engineering Materials, EarlyView.
This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley   +1 more source