Results 61 to 70 of about 1,180,561 (320)

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Calculation and control of DC bias current distribution in an AC power system around a typical ±800 kV DC grounding electrode

Jurnal Engineering, 2019
When the ultra-high-voltage direct current (UHVDC) transmission system operates in a monopolar ground return mode, an enormous DC current flows into earth via the DC grounding electrode in the converter station and then comes into the AC system around ...
Fangjie Wu, Shifeng Yu, Zhengkui Zhao, Wanlin Quan   +3 more
semanticscholar   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Reduction Of Electrode Grounding Impedance With Bentonite [PDF]

, 2011
One of an electrical protection goal is to make the lowest possible of grounding resistance. In this case, some earth fault current is homogenlydistributed throughcent the near by ground.
Widyaningsih, W. P. (Wiwik), Widyaningsih, Wiwik Purwati   +1 more
core  

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

A TLM‐Based Surge Analysis of Grounding Electrodes

Electrical Engineering in Japan, 2012
SUMMARYIn this paper, representations of a perfectly conducting thin wire and an imperfectly conducting medium in the transmission line modeling (TLM) calculation are briefly explained. Then, the method is applied to analyzing surge responses of a vertical parallelepiped grounding electrode and a square‐loop grounding electrode.
Yuda, Shinsuke, Baba, Yoshihiro, Nagaoka, Naoto, Ametani, Akihiro   +3 more
openaire   +1 more source

Electrified Damage in Motion Systems

Advanced Engineering Materials, EarlyView.
The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir, Angelina Nguyen, Hong Liang   +2 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source