Results 71 to 80 of about 3,855 (161)

Effect of Pulsating Current on 304HCU GTAW Joints

open access: yesInternational Journal of Engineering and Management Research, 2022
Super 304HCu super austenitic stainless-steel tubes containing 2.3 to 3 (Wt.%) Copper (Cu) are used in high temperature tubes and reheating of nuclear power plants. In general, stainless steel austenitic welded by conventional gas tungsten arc welding (CC-GTAW) now produces solid column grains, alloy disintegration and may result in lower mechanical ...
openaire   +1 more source

Effect of Nitrogen‐Added Shielding Gas on Microstructure Evolution of Welded Joints by Gas Tungsten Arc Welding Process in Duplex Stainless Steel 2205

open access: yessteel research international, Volume 95, Issue 5, May 2024.
A challenge in welding duplex stainless steels is to limit ferritization in the heat‐affected zone to ensure high corrosion resistance. The work describes the influence of nitrogen gas in the Ar–N2 shielding atmosphere during a gas tungsten arc welding process.
Bryan Ramiro Rodriguez‐Vargas   +3 more
wiley   +1 more source

On dissimilar metal welding of AISI4140 and AISI410 by GTAW

open access: yesIOP Conference Series: Materials Science and Engineering, 2017
This paper presents the results of metallurgical and mechanical examinations of Gas Tungsten Arc Welding of dissimilar steels AISI4140 and AISI410. Two different filler materials viz., ERNiCr3 and SS410 were used. The various properties of the weldments made using the fillers were compared to select the most appropriate one to get the sound joint.
M Velu, Shantanu Dixit, Shubham Choure
openaire   +1 more source

Visualisation of alternating shielding gas flow in GTAW [PDF]

open access: yesMaterials & Design, 2016
The alternating shielding gas technique is a method of achieving transient arc characteristics during arc welding; however the complex flow that occurs through its use has not been investigated previously. A schlieren system was used to image density gradients that arise when alternating argon and helium shield gases, under varying flow parameters ...
Bitharas, I.   +4 more
openaire   +4 more sources

Hot-Wire Gas Tungsten Arc Welding Cladding of Super Austenitic Stainless Steel on Low Carbon Steel

open access: yesApplied Sciences
Arc welding techniques for applying austenitic stainless steel cladding to low-carbon steels are common. Cladding enhances surface properties, increases corrosion resistance, improves product performance, extends service life, and reduces maintenance ...
Eli J. da Cruz   +7 more
doaj   +1 more source

A Study on the Corrosion Behavior in Sea Water of Welds Aluminum Alloy by Shielded Metal Arc Welding, Friction Stir Welding and Gas Tungsten Arc Welding

open access: yesInternational Journal of Electrochemical Science, 2015
Three types of welds aluminum alloy 6061 were prepared using shielded metal arc welding (SMAW), friction stir welding (FSW) and gas tungsten arc welding (GTAW). In addition for the first time borax powder was used with GTAW in weld region to increase the
Mustafa Özgür ÖTEYAKA, Hamdi AYRTÜRE
doaj   +1 more source

Review on Fatigue of Additive Manufactured Metallic Alloys: Microstructure, Performance, Enhancement, and Assessment Methods

open access: yesAdvanced Materials, Volume 36, Issue 17, April 25, 2024.
Additive manufactured metals have excellent mechanical properties, but their fatigue resistance is an exception. This article reviews the processes attributes, hierarchical microstructure, fatigue performance, and evaluation methods. The fatigue failure mechanisms of printed metals were summarized, and the competition between trans‐scale ...
Hui Liu   +7 more
wiley   +1 more source

Influence of surface treatment on metal dusting resistance of welds

open access: yesMaterials and Corrosion, Volume 75, Issue 3, Page 371-385, March 2024.
Fe contaminations enhanced metal dusting pit formation on brushed welds of Ni‐based alloys. The best performance of the welds was achieved by grinding, this is attributed to the deformation of the sub‐surface zone. Additional protection by on‐site slurry aluminization was successfully demonstrated.
Clara Schlereth   +5 more
wiley   +1 more source

Analysis and optimization of the automated TIG welding process parameters on SS304 incorporating Taguchi optimization technique

open access: yesThe Journal of Engineering, Volume 2024, Issue 3, March 2024.
The present research work focused on optimizing the input parameters of automated TIG welding process of SS304 metal. Since SS304 possess high inter‐granular toughness and corrosion resistance with increased lifespan in the pressure vessel and automobile component fabrication sector, its hardness and tensile strength response are undertaken for ...
Subramaniam Thangavel   +5 more
wiley   +1 more source

Galvanised steel to aluminium joining by laser and GTAW processes,

open access: yes, 2008
A new means of assembling galvanised steel to aluminium involving a reaction between solid steel and liquid aluminium was developed, using laser and gas tungsten arc welding (GTAW) processes.
Fras, Gilles   +10 more
core   +1 more source

Home - About - Disclaimer - Privacy