Results 121 to 130 of about 601,728 (278)
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
The Hölder continuity of spectral measures of an extended CMV matrix. [PDF]
J Math Phys, 2014 Munger PE, Ong DC.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Vector-valued Morrey's embedding theorem and Holder continuity in parabolic problems
Electronic Journal of Differential Equations, 2011 If $Isubset mathbb{R}$ is an open interval and $Omega subset mathbb{R}^N$ an open subset with $partial Omega $ Lipschitz continuous, we show that the space $W^{1,p}(I,L^q (Omega ))cap L^p(I,W^{1,q}(Omega ))$ is continuously embedded in $C^{0,frac{1 ...
Patrick J. Rabier
doaj
Advanced Engineering Materials, EarlyView.Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller +6 more
wiley +1 more source
Regularity of minimizers for double phase functionals of borderline case with variable exponents
Advances in Nonlinear AnalysisThe aim of this article is to study regularity properties of a local minimizer of a double phase functional of type ℱ(u)≔∫Ω(∣Du∣p(x)+a(x)∣Du∣p(x)log(e+∣Du∣))dx,{\mathcal{ {\mathcal F} }}\left(u):= \mathop{\int }\limits_{\Omega }({| Du| }^{p\left(x)}+a ...
Ragusa Maria Alessandra +1 more
doaj +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source