Results 31 to 40 of about 3,898,099 (355)
A simulated investigation on the machining instability and dynamic surface generation [PDF]
, 2005 In this paper, the authors propose the generic concept of machining instability based on the analysis of all kinds of machining instable behaviors and their features.
Altintas +13 more
core +1 more source
Journal of Manufacturing and Materials Processing, 2018 This article elucidates the characteristics of machining forces (an important phenomenon by which machining is studied) using three sets of bimetallic specimens made of aluminum–titanium, aluminum–cast iron, and stainless steel–mild ...
AMM Sharif Ullah
doaj +1 more source
The influence of laser assistance on the machinability of the titanium alloy Ti555-3 [PDF]
, 2013 The Ti533-3 alloy is a new titanium alloy which is starting to see increased use in the aeronautical domain to improve the durability of components and to optimize the weight/resistance ratio. This alloy is characterized by greater resistance compared to
BRAHAM-BOUCHNAK, Tarek +3 more
core +5 more sources
An experimental study of the effect of high-pressure water jet assisted turning (HPWJAT) on the surface integrity [PDF]
, 2011 This study deals with the effect of High-Pressure Water Jet Assisted Turning (HPWJAT) of austenitic stainless steels on chip shape and residual stresses. The machining of the austenitic stainless steels represents several difficulties. Recently, research
HABAK, Malek, LEBRUN, Jean-Lou
core +4 more sources
Residual Stresses in Machining of AISI 52100 Steel under Dry and Cryogenic Conditions: A Brief Summary [PDF]
, 2014 17th Conference on Material Forming (ESAFORM) - FinlandResidual stress is one of the most important surface integrity parameter that can significantly affect the service performance of a mechanical component, such as: contact fatigue, corrosion ...
BATISTA, Antonio +3 more
core +4 more sources
Lubricants, 2022 The use of lightweight materials, such as ultra-high-strength aluminium alloys, is in high demand in the automotive and aerospace industries where weight savings are critical.
Giselle Ramírez +7 more
doaj +1 more source
An overview of major research areas in Wire cut EDM on different materials [PDF]
INCAS Bulletin, 2020 WEDM (Wire electrical discharge machining) is a precision machining method for cutting electrically conductive materials. It is an unconventional machining process that produces precision parts that match the dimensional tolerances of our designs within ...
M. CHAITANYA REDDY, K. VENKATA RAO
doaj +1 more source
Automated soil hardness testing machine [PDF]
2007 14th International Conference on Mechatronics and Machine Vision in Practice, 2007 This paper describes the design and performance of a mechatronic system for controlling a standard drop-hammer mechanism that is commonly used in performing outdoor soil or ground hardness tests. A low-cost microcontroller is used to control a hydraulic actuator to repeatedly lift and drop a standard free-falling weight that strikes a pipe (sampler ...
Kumarapelige N. Sanathkumara +1 more
openaire +1 more source
Micromachines, 2021 Polycrystalline diamonds, polycrystalline cubic boron nitrides and tungsten carbides are considered difficult to process due to their superior mechanical (hardness, toughness) and wear properties.
K. Hazzan, M. Pacella, T. See
semanticscholar +1 more source
Laser surface texturing of a WC-CoNi cemented carbide grade: surface topography design for honing application [PDF]
, 2018 Abrasive effectiveness of composite-like honing stones is related to the intrinsic surface topography resulting from the cubic boron nitride (CBN) grains protruding out of the metallic matrix.
Bähre, Dirk +2 more
core +2 more sources