Results 71 to 80 of about 6,852 (304)
Simulating the Effects of Substrate Pre-Heating on the Final Structure of Steel Parts Built by Laser Powder Deposition [PDF]
, 2004 Tool steel parts built by laser powder deposition often present a heterogeneous distribution of properties caused by the complex structural transformations that occur during the deposition process.
Costa, L., Réti, T., Vilar, R.
core +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Physical metallurgy of modern creep-resistant steel for steam power plants: microstructure and phase transformations [PDF]
, 2016 The fact that the microstructure of steel depends on its composition and the heat treatment given to it has been heavily exploited in the design of steel for power plant applications.
Igwemezie, Victor C. +2 more
core +3 more sources
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
New Multiphase CP and DP 1000 MPa strength level grades for improved performance after hot forming [PDF]
, 2019 Pure martensitic steels have after hot forming limited performance in terms of rest ductility which limits the application in crash relevant parts. New steel grades were designed in the EU project HOTFORM including the corresponding process routes. These
Aranguren, Iñigo +6 more
core +1 more source
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Microstructural characterization of AISI 431 martensitic stainless steel laser-deposited coatings [PDF]
, 2011 High cooling rates during laser cladding of stainless steels may alter the microstructure and phase constitution of the claddings and consequently change their functional properties.
A Zambon +22 more
core +3 more sources
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
INFLUENCE OF MICROALLOYING BY BORON ON HARDENABILITY OF STEEL
Литьë и металлургия, 2016 The research conducted in laboratory of metallurgical science by which the factors exerting impact on hardenability of steel microalloyed by boron were analysed.
E. P. Baradyntseva +2 more
doaj