Results 121 to 130 of about 1,024 (244)
Experimental Investigation of the Impact Resistance of Involute Spur Gears
, 2018 Bu çalışma, 10-13, Temmuz 2018 tarihlerinde Budapest[Macaristan]’da düzenlenen 9. International Conference on Mechanical and Aerospace Engineering (ICMAE) Kongresi‘nde bildiri olarak sunulmuştur.Gears are the most commonly used power transmission element
Fatih Karpat +8 more
core +1 more source
Magnetic Barkhausen emission measurements for evaluation of material properties in gears
, 2008 The magnetic Barkhausen emission (MBE) technique is considered as a potential non-destructive evaluation (NDE) method for assessing material properties in case-hardened gears.
Moorthy V, Shaw BA
core
A New Method for Hardened Gears Machining - Ausform Finishing Process
, 2011 Ausform finishing process plastically deforms the surface of a steel component, generates compressive residual stresses in the surface layer, and imparts added strength and durability to the component.
Tong Jiang, Peng Zheng, Yan Bin Li
core +1 more source
The Effect of Residual Stress on Bending Strength of Induction Hardened Gears
Jixie chuandong, 1996 残余应力是影响感应淬火齿轮弯曲疲劳强度的重要而且复杂的因素之一，因为残余应力本身也受多种因素的影响。本文利用Ｘ射线衍射方法研究了各种感应淬火工艺及齿根拐角半径的影响，进而运用四点弯曲平板试样及标准试验齿轮研究了残余应力对其弯曲疲劳强度的影响。
陈国民, 阎满刚, 牛万斌
doaj
, 1998 The load-carrying capacity of medium hardness gears was investigated from the viewpoint of gear-manufacturing methods (hardness, gear accuracy and tooth surface roughness).
デン, ガン +11 more
core
HISTORY AND DEVELOPMENT DIRECTIONS OF INDUCTION HEATING HFC AT THE MINSK AUTOMOBILE PLANT
Литьë и металлургия, 2013 The data on the development of induction technology in the Republic of Belarus on the example of the Minsk Automobile Plant are given. Their development began at the end of the fifties at the Minsk Tractor Plant, and the highest development has been ...
P. S. Gurchenko, A. A. Shipko
doaj
, 2019 The paper deals with the mass optimization of gear pairs. The proposed material science based selection strategy uses an extended version of Ashby model, where the minimum value of mass as function of material parameters and density can be calculated ...
Czinege, Imre
core
Ingeniería Mecánica, 1999 Se exponen y discuten los inconvenientes de las clásicas y conocidas recomendaciones para decidir el espesor efectivo de capaendurecida en los dientes cementados de engranajes cilíndricos y cónicos.
G. González Rey
doaj
ANALYSIS OF RESIDUAL STRESSES IN THE HARDENED LAYER GEARS SKIDDERS CHEMICAL SINCE THE PROCESSING
Литьë и металлургия, 2015 The operating conditions of forest machines are analyzed. Transmission parts disabled as a result of intensive wear have been determined, their fracture mechanism has been established. A technique for diffuse impregnation of component parts with powdered
M. N. Pischov, E. P. Andreykovets
doaj
Limitations of the Check Calculation for Tooth Deformation of Plastic Gears According to Gear Design Guideline VDI 2736. [PDF]
Polymers (Basel), 2023 Herzog C, Drummer D.
europepmc +1 more source