Results 11 to 20 of about 22,871 (266)
TRIBOLOGICAL CONSIDERATIONS ON RWL 34 TOOLS STEEL [PDF]
Proceedings on Engineering Sciences, 2019 The paper presents an analyze of the tribological testing on the RWL 34 tools steels in diffrent stages: untreated, hardened and hardened and tempered. The wear tests were made by ball on disk, which is an oscilating sliding method.
Mihai DEMIAN +2 more
doaj +1 more source
Effect of Hollow Body Material on Mechanical Properties of Bubble Concrete
Crystals, 2022 The bubble concrete (BC) produced by mixing high-strength hollow bodies into concrete has been proven to be effective in reducing density while maintaining strength.
Xiangdong Yan +4 more
doaj +1 more source
Preparation and evaluation of gypsum plaster composited with copper smelter slag
Cleaner Engineering and Technology, 2021 Copper smelter slag is a by-product of copper production at smelters. In this paper, the slag was combined with gypsum, and the physical properties and functionalities of the resulting composites were evaluated to explore new uses for copper smelter slag.
Masahide Hagiri, Kazufumi Honda
doaj +1 more source
Characterization of cement composites based on recycled cellulosic waste paper fibres
Open Engineering, 2018 Nowadays, there is paying an attention to the utilization of natural, renewable and biodegradable resources of raw materials of lignocellulosic character, residues from agricultural crops and wood processing as well as waste from papermaking industry in ...
Stevulova Nadezda +4 more
doaj +1 more source
Comparison of Different Aerogel Granules for Use as Aggregate in Concrete
Gels, 2023 In previous work of this group, a structural lightweight concrete was developed by embedding silica aerogel granules in a high-strength cement matrix.
Torsten Welsch +4 more
doaj +1 more source
AcousticsIn order to measure the depth profile of the heat-treated case-hardened layer of linear guides, this paper proposes a B-scan imaging and 3D visualization method for detecting the depth profile of the case-hardened layer of linear guides based on the ...
Peiqiang Chen +3 more
doaj +1 more source
Theoretical Studies of Laws Nanostructuring and Heterogeneous Hardening of Steel Samples by Wave Intensive Plastic Deformation [PDF]
Журнал нано- та електронної фізики, 2015 Theoretical studies and calculations, allowing to define the required parameters of the wave deformation hardening, are performed in order to obtain heterogeneous hardened surface layer in steel samples.
A.V. Kirichek +3 more
doaj
Production and Manufacturing Research: An Open Access Journal, 2018 The quality of injection-moulded polymer optic parts depends on the surface finish of the respective mould. In order to improve the surface finish of the mould, it is important to use a tactical material removal, which allows a controlled correction of ...
Rui Almeida +4 more
doaj +1 more source
Influence of laser hardening modes on the properties of 40X13 steel
Весці Нацыянальнай акадэміі навук Беларусі: Серыя фізіка-тэхнічных навук, 2023 We have studied the dependence of the characteristics, strength and plasticity, as well as the microhardness of specimens made of corrosion-resistant steel 40X13 on the modes of laser surface hardening by a fiber laser.
O. M. Mishchiruk +4 more
doaj +1 more source
The hardening behaviour of cementitious materials [PDF]
Magazine of Concrete Research, 2001 Data from tests on samples of lime-pulverised fuel ash (PFA), lime–gypsum–PFA and cement–PFA mixtures have been analysed. In the case of the lime–PFA mixture, three phases of strength gain were identified, as follows. Phase 1—a rapid initial gain in strength, followed by an induction phase during which little or no strength gain was recorded. After an
M. Y. Abyaneh +3 more
openaire +1 more source