Results 131 to 140 of about 8,893 (267)
Cereal Chemistry, EarlyView.ABSTRACT Background and Objectives This study investigated how particle size influenced pasting and gelling behaviors of cereal flours across a wide range of heating temperatures. Hard wheat, soft wheat, oats, barley, and rye were milled into flours using 0.5‐, 1.0‐, or 2.0‐mm screens, and the resulting flours were subjected to heating over 95°C–140°C ...
Fan Cheng +6 more
wiley +1 more source
ZIF‐67 In Situ Grown PAN Spun Membrane Gel Electrolyte for Sodium‐Sulfur Batteries
Carbon Energy, EarlyView.This illustration shows the fabrication process of a solid‐state electrolyte for sodium‐sulfur (Na‐S) batteries. First, a polyacrylonitrile (PAN) fibrous membrane is prepared. Next, ZIF‐67 is grown in situ on the PAN membrane to form PAN@ZIF‐67. Subsequently, polyethylene oxide (PEO) is introduced into PAN@ZIF‐67 to obtain the composite electrolyte PEO/
Haowei Shi +4 more
wiley +1 more source
The Effect of Water Management and Cell Compression in Bipolar Membrane CO2 Electrolysis to CO
Carbon Energy, EarlyView.In‐operando neutron imaging uncovers water management challenges in bipolar membrane CO2 electrolysis: Internal water generation floods the cathode, while compression dictates membrane and gas diffusion electrode integrity. Strategic adjustments are applied in this work: dry gas feed and mechanical support of the gas diffusion electrode enable stable ...
Frederik Brendel +7 more
wiley +1 more source
Chemistry – A European Journal, EarlyView.Covalent linkage of a highly crystalline PHBV with a ductile P3HB4HB is shown to produce block copolymers with markedly enhanced extensibility and toughness, outperforming equivalent blends. The results demonstrate that polymer architecture, not composition alone, governs mechanical response, offering a route to biodegradable materials that combine ...
Katrin Blandine Kockler +3 more
wiley +1 more source
Review and prospects of shear test of bolted rock joints
Deep Underground Science and Engineering, EarlyView.The laboratory shear test equipment, test method, and numerical simulation of bolted rock joints were summarized. The shortcomings and limitations of the current research were analyzed, and the research prospects were proposed. Abstract Rock bolting is a critical approach in geotechnical engineering for supporting weak rocks.
Shulin Ren +4 more
wiley +1 more source
Deep Underground Science and Engineering, EarlyView.A novel shear‐lag model, validated by pull‐out tests, incorporates a constant bond stress stage to predict the complete load–displacement response of grouted rock bolts, providing a new tool for optimizing anchorage length and material toughness in deep underground engineering. Abstract The stability of rock masses in deep underground excavations, such
Wenhui Bian +6 more
wiley +1 more source
Deep Underground Science and Engineering, EarlyView.An analytical framework delivers a closed‐form stress solution for lined compressed air energy storage chambers, enabling the determination of the minimum safe burial depth. The solution quantitatively evaluates lining support effectiveness, offering a reliable tool for chamber design and optimization.
Zeyuan Sun +3 more
wiley +1 more source
Study on D6AC Steel PCBN Hard Turning and Optimization. [PDF]
Materials (Basel)Liu Y +5 more
europepmc +1 more source
Deep Underground Science and Engineering, EarlyView.Through shear–tensile creep tests and viscoelastic modeling, the fracture evolution of thick soft protective layers is clarified. Results show thickness‐dependent rheological failure modes that govern four types of roof water inrush, providing a mechanism‐based framework for hazard prediction and control. Abstract In the Jurassic coal‐bearing strata of
Mengnan Liu +4 more
wiley +1 more source
The Effect of Laser Surface Hardening on the Microstructural Characteristics and Wear Resistance of 9CrSi Steel. [PDF]
Materials (Basel)Sagdoldina Z +5 more
europepmc +1 more source