Results 11 to 20 of about 226,462 (213)
Heliyon, 2021 In engineering projects (dams, tunnels, slope stability) the strength characteristics of the rocks affect the construction operations. It is sometimes difficult, time-consuming, and expensive to evaluate the engineering properties of solid rocks by ...
Ahmet Teymen
doaj +1 more source
Hardness relationship between eNM3A10 and conventional hardness scales
Measurement: Sensors, 2021 Small ball rebound hardness eNM3A10 is a next-generation rebound hardness test with features not existing in conventional rebound hardness tests: reduced mass effect of hardness and satisfying the similarity rule of hardness (Minimum thickness of steel ...
Takashi Yamamoto +2 more
doaj +1 more source
Enhanced thermal stability and fracture toughness of TiAlN coatings by Cr, Nb and V-alloying [PDF]
, 2018 The effect of metal alloying on mechanical properties including hardness and fracture toughness were investigated in three alloys, Ti~0.33Al0.50(Me)~0.17N (Me¿=¿Cr, Nb and V), and compared to Ti0.50Al0.50N, in the as-deposited state and after annealing ...
Andersson, J. M. +7 more
core +2 more sources
Acta Odontologica Turcica, 2017 Objective: The aim of this study was to compare the effects of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and 1.23% acidulated phosphate fluoride (APF; pH 3.5) on the microhardness of enamel treated with a bleaching agent. Materials and
Mügem Aslı Gürel Ekici +3 more
doaj +1 more source
The contribution of 211 particles to the mechanical reinforcement mechanism of 123 superconducting single domains [PDF]
, 2003 Hardness and fracture toughness of Dy-123 single-domains were studied by Vickers micro-indentation. A significant anisotropy of the mechanical properties was observed. Hardness tests give higher values when performed in (001) planes rather than in planes
Ausloos, M. +7 more
core +2 more sources
Microstructural and Corrosion Properties of Cold Rolled Laser Welded UNS S32750 Duplex Stainless Steel [PDF]
, 2018 The main goal of this work was to study the effect of plastic deformation on weldability of duplex stainless steel (DSS). It is well known that plastic deformation prior to thermal cycles can enhance secondary phase precipitation in DSS which can lead to
B\uf6gre, Balint +5 more
core +1 more source
Evaluation of photo-activation appliances used in dentistry [PDF]
RGO: Revista Gaúcha de Odontologia, 2008 Objective: Verify the Vickers microhardness promoted by three photo-activation appliances: one Halogen Light Ultralux (Dabi-Atlante, Ribeirão Preto, Brazil) and two Light Emitting Diodes.
Thales Ribeiro de Magalhães Filho +5 more
doaj
Dual morphology (fibres and particles) cellulosic filler for WPC materials [PDF]
, 2016 Wood-plastic composites (WPC) were fabricated by using a polyethylene (PE) matrix and filling it with wood flour in the amount of 30 wt.%, and compared with the same composites with further amount of 10 wt.% of cellulosic recycled fibres added.
QUITADAMO, ALESSIA +3 more
core +1 more source
Basic mechanical properties of layered steels
Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 2013 This article deals with identifying attributes of layered steel materials (damask steel) with the help of mechanical tests. Experimentally verify basic mechanical properties of layered steel and subsequently assessed it in comparison with the values ...
Michal Černý +3 more
doaj +1 more source
HV/HR-CMOS sensors for the ATLAS upgrade—concepts and test chip results [PDF]
, 2015 In order to extend its discovery potential, the Large Hadron Collider (LHC) will have a major upgrade (Phase II Upgrade) scheduled for 2022. The LHC after the upgrade, called High-Luminosity LHC (HL-LHC), will operate at a nominal leveled instantaneous ...
Backhaus, M. +39 more
core +2 more sources