Results 191 to 200 of about 52,550 (264)

Moisture-Curable Poly(hydroxyurethanes) Composites Reinforced with Silica Nanofillers. [PDF]

Polymers (Basel)
Bride T, Laurent E, Raad J, Marić M.
europepmc   +1 more source

Wearable Morphology‐Adaptive in‐Ear Device With Active Cleansing Capability for Multimodal Health Monitoring

Advanced Materials, EarlyView.
We present SCIENCE, an in‐ear multimodal physiological monitor featuring two key innovations. Water‐triggered morphological expansion (a 2‐mm cylinder to a 9‐mm spindle) achieves conformal adaptation across complex canal geometries. Simultaneously, active biofouling mitigation disrupts cerumen barriers, reducing sensor‐skin impedance by 20%.
Shuyun Zhuo, Zihuan Wu, Anan Zhang, Shideh Kabiri Ameri   +3 more
wiley   +1 more source

Microstructural Evolution and Mechanical Properties of Investment-Cast Haynes 282 Nickel-Based Superalloy After Heat Treatment and High-Temperature Thermomechanical Processing. [PDF]

Materials (Basel)
Nowotnik A, Wichowska E, Mrowka-Nowotnik G.   +2 more
europepmc   +1 more source

Breaking the Surface: Buoyant Metal–Polymer Open–Cell Hybrid Lattice Metamaterials

Advanced Materials, EarlyView.
Open‐cell metal–polymer lattice metamaterials that defy sinking. (a) Injection process of the polyurethane (PU) foam into the titanium (Ti‐6Al‐4V) hollow‐strut lattice creating the open‐cell Ti‐6Al‐4V+PU hybrid lattice, (b) flotation test of a hybrid lattice specimen, and (c) a digital representation and experimental validation of a marine buoy ...
Jordan Noronha, Joey Tallon, Raad Omar, Jason Dash, Andrey Molotnikov, Martin Leary, Milan Brandt, Ma Qian   +7 more
wiley   +1 more source

Assessment of the Strength of Welded Joints in a Gas Pipeline Using FEM Modeling. [PDF]

Materials (Basel)
Zvirko O, Dzioba I, Pała T, Demianchuk D, Tsyrulnyk O.   +4 more
europepmc   +1 more source

Soft Yet Tough Tanglemers Through Rapid Photopolymerization for DLP 3D Printing

Advanced Materials, EarlyView.
Soft yet tough tanglemers are produced through low‐initiator free radical photopolymerization and translated to DLP 3D printing. Systematic control over light intensity, initiator loading, and crosslink density reveals processing windows that balance printability, elasticity, toughness, and feature fidelity. ABSTRACT Additive manufacturing of compliant
Yutong Liu, Tiffany N. Jeng, Elizabeth A. Recker, Ellen J. Forehand, Gabriel E. Sanoja, Zachariah A. Page   +5 more
wiley   +1 more source

Knowledge-informed graph attention networks enable defect-free alloy design for laser additive manufacturing. [PDF]

Nat Commun
Fu J, Yu H, Wang C, Wang L, Sun Z, Li J, van der Zwaag S, Raabe D, Xu W.   +8 more
europepmc   +1 more source

Interfacial Failure and Self‐Healing in Solid‐State Batteries

Advanced Materials, EarlyView.
Dynamic interfacial self‐healing offers an adaptive route to mitigate coupled mechanical, chemical, and electrochemical degradation in solid‐state batteries. This review connects evolving interfacial failure mechanisms with physical‐flow, chemical‐restoration, stimuli‐responsive, and electric‐field‐assisted repair strategies, highlighting targeted self‐
Xinxin Zhu, Tengfei Dai, Wendi Dou, Zhiheng Li, Kaihua Wen, Yanqun Lv, Ming Zhao, Jun Lu, Zaiping Guo   +8 more
wiley   +1 more source

Hetero-deformation induced stress and its microstructural morphology dependence in a near-alpha titanium alloy. [PDF]

PLoS One
Xie L, Li J, Xing Y, Wang Y.
europepmc   +1 more source