Results 111 to 120 of about 10,838 (210)

Thermo-Reactively Coupled (TRC) HDPE for Melt-Processable Warp-Resistant FDM 3D Printing. [PDF]

Polymers (Basel)
Ash S, Naveed M, Rabnawaz M.
europepmc   +1 more source

Impact of Waste‐Derived Slate Dust on Structural, Thermal, and Thermomechanical Behavior of Recycled Poly(Ethylene Terephthalate)

Polymer Composites, Volume 47, Issue 20, Page 18206-18221, 20 October 2026.
This study investigates the use of waste slate dust as a filler in recycled PET. Incorporating up to 20 wt% slate dust caused no filler‐induced molecular degradation, increased the crystallization temperature, thermal conductivity, and storage modulus. ABSTRACT Recycled polyethylene terephthalate (rPET) is widely considered a sustainable alternative to
Aditya Chauhan, Tej Singh, Andrea Fiorati, Sampat Singh Bhati, László Lendvai, Luigi De Nardo, Robert Brüll   +6 more
wiley   +1 more source

Evaluation of Mechanical and Durability Performance of Concrete with and Without Surface-Treated Plastic Fine Aggregates. [PDF]

Materials (Basel)
Ikkurthi S, Dai Q.
europepmc   +1 more source

Effect of Temperature on the Tensile Mechanical Properties and Creep Performance of Wood-plastic Composites

BioResources
Uniaxial tensile tests of recycled waste wood plastic composites were conducted at 20, 40, and 60 °C. High density polyethylene (HDPE, 30%) was reinforced with poplar wood (50%), and calcium carbonate (15%), with 5% additives.
Fei Xi, Jun Yang, Longlong Zhao, Yang Wei   +3 more
doaj  

Local Yield Stress Distribution of HDPE Pipe Butt Fusion Joints Measured by a Small Punch Test. [PDF]

Polymers (Basel)
Bai C, Duan X, Hu Z, Lai HS, Zhong Y, Du P.   +5 more
europepmc   +1 more source

Characterization of animal tissues for Monte Carlo simulations in ion beam therapy

Journal of Applied Clinical Medical Physics, Volume 27, Issue 10, October 2026.
Abstract Purpose To obtain better elemental compositions (ECs), physical densities (PDs), and relative linear stopping powers (RLSPs) of tissues scanned by single or dual energy computed tomography for use by Monte Carlo (MC) simulations of light ion beam therapy.
Liu Xiaoli, Michael F. Moyers
wiley   +1 more source

Dosimetric evaluation of patient-side range shifters using two materials for superficial region treatment in spot scanning proton therapy: impact of material, air gap and setup distance. [PDF]

J Radiat Res
Ota S, Kajikawa T, Ogata T, Takaya H, Kijima K, Okita T, Aibe N.   +6 more
europepmc   +1 more source

Defect‐Engineered Microwave‐Responsive Ni@C Composites From Waste PET for Catalytic Plastic Upcycling

Advanced Materials, Volume 38, Issue 57, 13 October 2026.
A circular upcycling strategy transforms waste poly(ethylene terephthalate) bottles into microwave‐responsive Ni@C catalyst featuring lattice‐distorted nickel cores and defective carbon shells. These strain‐rich heterointerfaces enhance dielectric loss and promote localized microwave hotspots, accelerating peroxymonosulfate activation and polymer‐chain
Xiao Lu, Shiying Ren, Jingkai Lin, Kunsheng Hu, Yalan Mo, Shaobin Wang, Wenjie Tian, Xiaoguang Duan   +7 more
wiley   +1 more source

Life-Cycle Assessment of Laboratory-Scale Extrusion of Virgin and Recycled Polyolefins: Influence of Operating Duration on Life-Cycle Inventory Development. [PDF]

Polymers (Basel)
Saleem J, Moghal ZKB, Mckay G.
europepmc   +1 more source

Enhanced Mechanical Recycling of Polymer Mixtures by a Trifunctional Dynamic Crosslinker

Advanced Materials, Volume 38, Issue 58, 16 October 2026.
A self‐catalyzed, trifunctional dynamic crosslinker that incorporates three desired properties into one system and is compatible with reactive extrusion can compatibilize waste plastic mixtures containing high Tm polymers and impart the recycled mixtures with superior thermoset properties such as enhanced creep resistance and thermomechanical stability
Xavier Westworth, Essa Shamsan, Yunpeng Gao, Nevaya Carr, Eugene Y.‐X. Chen   +4 more
wiley   +1 more source