Results 81 to 90 of about 217,040 (256)
Литьë и металлургия, 2006 The comparison of the results of the temperature regimes of the heating furnace with pacing backstone with experimental data, received in terms of operating production at working of furnace with varied capacity is carried out.
V. I. Timoshpolskij +4 more
doaj
Arthritis Care &Research, EarlyView.Objective Although the definition of a gout flare is well established, the state of gout flare resolution has not yet been defined. This study aimed to explore patients’ experiences and perceptions of gout flare resolution. Methods Semistructured interviews were conducted with 24 people with gout, guided by open‐ended questions exploring their ...
Sarah Stewart +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares +3 more
wiley +1 more source
Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy
Advanced Engineering Materials, EarlyView.This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb +6 more
wiley +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee +7 more
wiley +1 more source
Digital Technologies Application in Diesel Engine Design: from Concept to Serial Production
Механика машин, механизмов и материаловThe paper presents the key aspects of using digital technologies in mechanical engineering covering the stages of design and technological preparation of production.
Igor A. Popov +5 more
doaj +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source