Results 181 to 190 of about 1,658,583 (289)

Fast differential scanning calorimetry to mimic additive manufacturing processing: specific heat capacity analysis of aluminium alloys. [PDF]

J Therm Anal Calorim, 2023
Quick CR, Dumitraschkewitz P, Schawe JEK, Pogatscher S.   +3 more
europepmc   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Thermophysical Characterization of [C₆mim][SbF₆] Ionic Liquid as a Heat Transfer Fluid: Heat Capacity, Thermal Conductivity, and Viscosity. [PDF]

ACS Omega
Liang K, Liang L, Yao H, Qiao J, Fu D, Fang D.   +5 more
europepmc   +1 more source

On the Possible Nature of Armchair-Zigzag Structure Formation and Heat Capacity Decrease in MWCNTs. [PDF]

Materials (Basel), 2022
Ponomarev A, Egorushkin V, Bobenko N, Barabashko M, Rezvanova A, Belosludtseva A.   +5 more
europepmc   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

On the Mechanism of Soft Self-Assembly from Melt: The Ubiquitous Heat Capacity Hump and Spontaneous Melt Chirality. [PDF]

Angew Chem Int Ed Engl
Xue YN, Zeng XB, Wu BW, Li YX, Cseh L, Yang SG, Liu J, Gehring GA, Liu F, Ungar G.   +9 more
europepmc   +1 more source

Thermal fluids with high specific heat capacity through reversible Diels-Alder reactions. [PDF]

iScience, 2022
Lilley D, Yu P, Ma J, Jain A, Prasher R.
europepmc   +1 more source

Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC

Advanced Engineering Materials, EarlyView.
ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko, Evelyn Wang, Michael A. Hickner   +2 more
wiley   +1 more source

Experimental heat capacity of highly stable diamond/thermal oil nano-suspensions. [PDF]

RSC Adv
Ahmed A, Ilyas SU, Noshad N, Alsaady M, Abdulrahman A, Mahfouz AB, Ali A.   +6 more
europepmc   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source