Results 231 to 240 of about 4,691,836 (302)

Comparative Evaluation of LED Light Application and Heat Generation with Three Different Wavelengths of Frequency on Soft Tissues in Bringing Faster Orthodontic Tooth Movement: A Finite Element Model Study. [PDF]

J Biomed Phys Eng
Riyaz K, G Shivamurthy P.
europepmc   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

The Effect of Dental Implant Drills Materials on Heat Generation in Osteotomy Sites: A Systematic Review. [PDF]

Eur J Dent
Chakraborty S, Moufti MA, Kheder W.
europepmc   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

Modeling and Experimental Investigation of the Impact of the Hemispherical Tool on Heat Generation and Tensile Properties of Dissimilar Friction Stir Welded AA5083 and AA7075 Al Alloys. [PDF]

Materials (Basel)
Essa ARS, Eldersy RIA, Ahmed MMZ, Abd El-Aty A, Alamry A, Alzahrani B, El-Nikhaily AE, Habba MIA.   +7 more
europepmc   +1 more source

Steel drills versus zirconia drills on heat generation at the surgical site of dental implants: A systematic review and meta-analysis. [PDF]

Saudi Dent J
Augusto Alves Bento V, Marcela de Luna Gomes J, Davi Del Rei Daltro Rosa C, Pedro Justino de Oliveira Limirio J, Micheline Dos Santos D, Coelho Goiato M, Piza Pellizzer E.   +6 more
europepmc   +1 more source