Results 191 to 200 of about 8,455,902 (295)

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Multi-Component Coatings Enabling Low-Toxicity and Self-Extinguishing Polyurethane Foams with Potential for Railway Fire Safety. [PDF]

Polymers (Basel)
Kabir II, Brehme S, Schartel B.
europepmc   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Recent Advances in Phase-Change-Coupled Interfacial Evaporation: Thermal-Mass Management and Multifunctional Applications. [PDF]

Nanomaterials (Basel)
Li X, Chen Q, Li X.
europepmc   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

Advanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika, Hunter Kantelis, Yogesh K. Vohra, Shengbiao Zhang, Wuxian Yang, Wen Chen   +5 more
wiley   +1 more source

Preparation of an Ester-Based Polymeric Hydration Temperature Rise Inhibitor and Its Action Mechanism on Cement Hydration. [PDF]

Polymers (Basel)
Li Q, Li T, Li X, Mei H, Chen J, Liu M, Yan C.   +6 more
europepmc   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

Advanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe, Louis Becker, Gaurav Kanu, Thomas F. Headen, Dirk Honecker, Gabi Schierning, Santiago Benito, Sebastian Weber, Klara Lünser, Sabrina Disch   +9 more
wiley   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Engineering Strategies to Suppress Thermal Runaway Propagation in Lithium-Ion Battery: Mechanisms, Metrics, Materials, and Evaluation Methods. [PDF]

Adv Sci (Weinh)
Su J, DiFelice A, Mawela J, Gan J, Che S, Cho W, Yan H, Xiao Y, Yao X, Guo X, Wang R, Xue D, Liu H, Adera S, Chen Z, Chen L.   +15 more
europepmc   +1 more source

Influence of Fe Particle Size Distribution on Chemical Homogeneity, Microstructure, and Crack Formation in Fe–SiC Powder Blends Processed by PBF‐LB/M

Advanced Engineering Materials, EarlyView.
The influence of Fe particle size on in situ alloying of Fe–SiC powder blends in PBF‐LB/M is revealed. Contrary to expectations, the coarser Fe fraction provides a broader crack‐free processing window and slightly improved elemental homogeneity while producing higher but more variable hardness. The results highlight a complex trade‐off between particle
Anna Luise Strauch, Anastasiya Toenjes, Matthias Steinbacher   +2 more
wiley   +1 more source