Results 141 to 150 of about 352,836 (265)

Study of Boiling Heat Transfer of R417A on Horizontal Doubly-enhanced Tubes

Zhileng xuebao, 2014
Experimental studies of boiling heat transfer of R417A on three single horizontal doubly-enhanced tubes have been conducted at the saturation temperature of 8 ℃.
Zhang Dingcai, Tian Songna, Ji Wentao, Zhao Anli, Fan Xiaowei, Tao Wenquan   +5 more
doaj  

Heat transfer analysis of the forced air quenching with non-isothermal and non-uniform oxidation. [PDF]

PLoS One, 2021
Zhang Y, Yang J, Gao MX, Sono H.
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Review of heat transfer analysis [PDF]

, 1965
openaire   +2 more sources

Experimental analysis of heat transfer coefficient in the plate heat exchanger

, 2011
In this study, heat transfer coefficient of plate heat exchanger was experimentally investigated. Plate heat exchanger into experimental mechanism was set. Different tests by varying of mass flow rates and inlet temperatures were carried out. Analyses of obtained results were performed. Variation of heat transfer coefficient of plate heat exchanger was
openaire   +2 more sources

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Hydrodynamic and heat transfer analysis of dissimilar shaped nanoparticles-based hybrid nanofluids in a rotating frame with convective boundary condition. [PDF]

Sci Rep, 2022
Ramzan M, Shahmir N, Ghazwani HAS, Nisar KS, Alharbi FM, Yahia IS.   +5 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Development & application of a wearable non-differential calorimeter for skin heat transfer analysis. [PDF]

PLoS One
Rodríguez de Rivera PJ, Rodríguez de Rivera M, Socorro F, Rodríguez de Rivera M.   +3 more
europepmc   +1 more source

Heat transfer analysis of Cu and Al₂O₃ dispersed in ethylene glycol as a base fluid over a stretchable permeable sheet of MHD thin-film flow. [PDF]

Sci Rep, 2022
Zeeshan, Khan I, Weera W, Mohamed A.
europepmc   +1 more source