Results 141 to 150 of about 185,741 (267)

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Study of Heat Transfer Characteristics of PCMs Melting Inside Aluminum Foams. [PDF]

Materials (Basel)
Khan FSH, Diani A.
europepmc   +1 more source

Numerical Study on Flow and Heat Transfer Characteristics of Trapezoidal Printed Circuit Heat Exchanger. [PDF]

Micromachines (Basel), 2021
Ji Y, Xing K, Cen K, Ni M, Xu H, Xiao G.
europepmc   +1 more source

CHARACTERISTICS OF HEAT TRANSFER IN ROOM INTERIOR (2) : Overall Heat Transfer and Characteristics of Heat Transfer in a Non-ventilated Room

Transactions of the Architectural Institute of Japan, 1980
openaire   +2 more sources

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Numerical simulation on heat transfer characteristics of a bionic leaf-vein fractal fin heat exchanger. [PDF]

Sci Rep
Wang R, Hou Y, Yu H, Xing M.
europepmc   +1 more source

Transient Heat Transfer Characteristics in a Flat Plate Heat Sink with Mini-Channels for Cooling High Heat Flux IGBT. [PDF]

Micromachines (Basel), 2022
Chen C, Zhao H, Liu C, Chen J, Liu C, Zhang T, Gong W.   +6 more
europepmc   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Experimental study on heat transfer characteristics of plate evaporator under heaving, pitching, and rolling conditions. [PDF]

Sci Rep
Chen H, Yu B, Zhang Y, Zhou Y, Li C, Wu Y, He X, Hua D, Zhang C.   +8 more
europepmc   +1 more source

Numerical Investigation of Heat Transfer Characteristics of scCO₂ Flowing in a Vertically-Upward Tube with High Mass Flux. [PDF]

Entropy (Basel), 2022
Gong K, Zhu B, Peng B, He J.
europepmc   +1 more source