Results 131 to 140 of about 74,370 (244)

Heat Transfer Enhancement [PDF]

, 2006
openaire   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Heat Transfer Enhancement of Small-Diameter Two-Phase Closed Thermosyphon Using Cellulose Nanofiber and Hydrophilic Surface Modification. [PDF]

Nanomaterials (Basel), 2021
Choi D, Jun G, Hwang W, Lee KY.
europepmc   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Enhanced heat transfer

The heat transfer performance of all the developed materials for dropwise condensation will be evaluated in custom condensation setups.
openaire   +1 more source

Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC

Advanced Engineering Materials, EarlyView.
ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko, Evelyn Wang, Michael A. Hickner   +2 more
wiley   +1 more source

Heat transfer enhancement in a parabolic trough collector using finned tubular absorber. [PDF]

Sci Rep
Donga RK, Kumar S, Velidi G.
europepmc   +1 more source

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Heat transfer enhancement of a solar air heater using capsule-shaped turbulators: a numerical analysis. [PDF]

Sci Rep
Madhwesh N, Karanth KV, Kumar S.
europepmc   +1 more source

Engineered Mycelial Scaffolds With Tunable Ultraviolet Protection, Wettability, Thermal Stability, and Spatial Mechanics

Advanced Engineering Materials, EarlyView.
Fungal mycelia grown into biodegradable scaffolds and infused with titania nanoparticles show enhanced ultraviolet shielding, thermal protection, and surface nonwettability. Properties were tuned by drying methods, revealing structure–function relationships.
Juwon S. Afolayan, Xin Zhang, Carole C. Perry   +2 more
wiley   +1 more source