Results 191 to 200 of about 2,321,244 (303)

Influence of Dual Heat Treatment on the Metallurgy and Mechanical Behaviour of Diamond-Like Carbon-Coated NiTi Rotary Systems: A Multimethod Investigation. [PDF]

Int Endod J
Silva EJNL, Cardoso TO, Martins JNR, Fernandes FMB, Vieira VTL, Versiani MA.   +5 more
europepmc   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Effect of Pressure-Assisted Heat Treatment on the Crystalline Phase of Titanium Dioxide, Niobium Pentoxide, and Ruthenium-Modified Oxides. [PDF]

ACS Omega
Pires PB, Fuziki MEK, Lenzi GG, Sabino SDRF, Novatski A, Tebcherani SM, Dias DT.   +6 more
europepmc   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Synthesis and Characterization of CuO Nanoparticles Using Heat Treatment Approach: Annealing Effects on Crystallite Size and Band Gap of CuO Nanoparticles. [PDF]

ACS Omega
Maria KH, Rodriguez Bonet SG, Bosco MV, Bin Salam SR, Dhar D, Nazzarro M, Furlong OJ, Calaza FC.   +7 more
europepmc   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Mg-3.2Nd-2.5Gd-0.4Zn-0.5Zr (wt.%) Alloy. [PDF]

Materials (Basel)
Li Y, Cui J, Liu H, Mu T, An L, Zhang Y, Yu Q, Zhang H, Ye X.   +8 more
europepmc   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Effect of Heat Treatment on In Vitro Cytotoxicity of Ti-Nb-Zr Gum Metal Alloy. [PDF]

Materials (Basel)
Etemad A, Hasani S, Mashreghi A, Heidari F, Salehikahrizsangi P, Schwarz S, Bloch K, Nabialek M.   +7 more
europepmc   +1 more source