Results 191 to 200 of about 873,914 (307)

Microstructure Optimization of Thermoelectric τ₁-Al₂Fe₃Si₃ via Graded Temperature Heat Treatments. [PDF]

Materials (Basel)
Yurishima R, Takagiwa Y, Ikeda A, Ikeda T.   +3 more
europepmc   +1 more source

Improvement of Tool Steel Powder Cold Sprayability Via Softening and Agglomeration Heat Treatments. [PDF]

J Therm Spray Technol, 2022
Poirier D, Thomas Y, Guerreiro B, Martin M, Aghasibeig M, Irissou E.   +5 more
europepmc   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Effects of Cold Deformation and Heat Treatments on the Microstructure and Properties of Fe-15Cr-25Ni Superalloy Cold-Drawn Bars. [PDF]

Nanomaterials (Basel)
Zhang Y, Zhang Z, Sun Z, Zhao Y, Cui Y, Zhang Z.   +5 more
europepmc   +1 more source

Effect of Various Heat Treatments on the Microstructure of 316L Austenitic Stainless Steel Coatings Obtained by Cold Spray. [PDF]

J Therm Spray Technol, 2022
Brassart LH, Besson J, Delloro F, Haboussa D, Delabrouille F, Rolland G, Shen Y, Gourgues-Lorenzon AF.   +7 more
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Phase Evolution of Li-Rich Layered Li-Mn-Ni-(Al)-O Cathode Materials upon Heat Treatments in Air. [PDF]

Materials (Basel)
Grins J, Jaworski A, Jøsang LO, Biendicho JJ, Svensson G.   +4 more
europepmc   +1 more source

Fatty Acids Profile and Healthy Lipids Indices of Native Mexican Guajolote Meat Treated to Two Heat Treatments. [PDF]

Foods, 2022
Cigarroa-Vázquez FA, Granados-Rivera LD, Portillo-Salgado R, Ventura-Ríos J, Esponda-Hernández W, Hernández-Marín JA, Cruz-Tamayo AA, Bautista-Martinez Y.   +7 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Impact of ultrasonic and heat treatments on the physicochemical properties and rennet-induced coagulation characteristics of milk from various species. [PDF]

Ultrason Sonochem
Hou W, Ma X, Yu Z, Bari L, Jiang H, Du Q, Fan R, Wang J, Yang Y, Han R.   +9 more
europepmc   +1 more source