Results 61 to 70 of about 55,028 (261)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
FibersSprings are widely used in industries such as aerospace and automotive. As the demand for emission reduction grows, the research on lightweight spring performance is becoming increasingly important.
Yupu Dai +3 more
doaj +1 more source
Helical-Bevel Gearing with Small Wheel Axles Angles
Procedia Engineering, 2017 Abstract The design of special purpose gear mechanisms in engineering requires using gearings with small angles between the wheel axles. Frequently, the task to make such gearings based on traditional gearings (cylindrical and bevel) with the required layout and operation features fails.
B.A. Lopatin, S.V. Plotnikova
openaire +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
DESIGN AND PERFORMANCE OF A 300-WATT HELICAL TYPE H-ROTOR WIND TURBINE
Rekayasa MesinThe Helical Type H-rotor turbine is a modification of the Darrieus turbine by Alexander Gorlov to improve the design of the H-Darrieus so the turbine can self-starting in low wind speed conditions. The purpose of this study is to analyze the pitch angle (
Diniar Mungil Kurniawati +4 more
doaj +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Contact Stress Analysis for Gears of Different Helix Angle Using Finite Element Method
MATEC Web of Conferences, 2014 The gear contact stress problem has been a great point of interest for many years, but still an extensive research is required to understand the various parameters affecting this stress.
Patil Santosh +4 more
doaj +1 more source