Results 171 to 180 of about 1,427,164 (255)
High Cycle Fatigue Performance of LPBF 304L Stainless Steel at Nominal and Optimized Parameters. [PDF]
Materials (Basel), 2020 Parvez MM +5 more
europepmc +1 more source
HIGH CYCLE FATIGUE OF PRESTRAINED COMPONENTS
, 1978 M. Bílý, V. Kliman, P. Ľubušký
openaire +2 more sources
Very High-Cycle Fatigue and High-Cycle Fatigue of Minor Boron-Modified Ti–6Al–4V Alloy
MATERIALS TRANSACTIONS, 2019 Masuo Hagiwara +4 more
openaire +2 more sources
Some of the next articles are maybe not open access.
Related searches:
Related searches:
Specific features of high‐cycle and ultra‐high‐cycle fatigue
Fatigue & Fracture of Engineering Materials & Structures, 2002ABSTRACT Several specific features of high‐cycle fatigue (HCF) and ultra‐high‐cycle fatigue (UHCF) are discussed both on the basis of direct experimental results and on the basis of speculations extrapolating HCF data to the UHCF regions. The following points are dealt with: (i) Extent and distribution of cyclic plastic deformation. (ii) Sensitivity of
P. LUKÁŠ, L. KUNZ
openaire +2 more sources
High cycle fatigue in selective laser melted Ti-6Al-4V
Acta Materialia, 2020A major drawback of additively manufactured metallic components is their poor high cycle fatigue (HCF) resistance, which is primarily due to the presence of porosity in them. Keeping this in view, the effect of process parameters such as laser power (w),
Punith Kumar, U. Ramamurty
semanticscholar +3 more sources
, 2021
The high-cycle fatigue (HCF) properties and deformation behavior of additively manufactured equiatomic CoCrFeMnNi high-entropy alloys (HEAs), strengthened by in-situ formed oxides, were investigated.
Young-Kyun Kim +3 more
semanticscholar +1 more source
The high-cycle fatigue (HCF) properties and deformation behavior of additively manufactured equiatomic CoCrFeMnNi high-entropy alloys (HEAs), strengthened by in-situ formed oxides, were investigated.
Young-Kyun Kim +3 more
semanticscholar +1 more source
Materials Science & Engineering: A, 2021
The high-cycle fatigue properties and fatigue damage mechanism of AlSi10Mg alloy manufactured by selective laser melting (SLM) were investigated. The influence of the post-heat treatment on the microstructure and high-cycle fatigue properties was also ...
M. Baek +4 more
semanticscholar +1 more source
The high-cycle fatigue properties and fatigue damage mechanism of AlSi10Mg alloy manufactured by selective laser melting (SLM) were investigated. The influence of the post-heat treatment on the microstructure and high-cycle fatigue properties was also ...
M. Baek +4 more
semanticscholar +1 more source
, 2021
Tensile and fatigue behaviors of a compressor blade titanium alloy TC17 at room and high temperatures (RT and HT) have been investigated up to very high cycle fatigue (VHCF) regime. Compared to RT, the HT tensile strength of TC17 titanium alloy decreases,
Fulin Liu +8 more
semanticscholar +1 more source
Tensile and fatigue behaviors of a compressor blade titanium alloy TC17 at room and high temperatures (RT and HT) have been investigated up to very high cycle fatigue (VHCF) regime. Compared to RT, the HT tensile strength of TC17 titanium alloy decreases,
Fulin Liu +8 more
semanticscholar +1 more source
International Journal of Fatigue, 2021
Crack initiation mechanisms under two stress ratios (R = − 1 and 0.5) and up to very-high-cycle fatigue (VHCF) regime of a selective laser melted (SLMed) Ti-6Al-4V were investigated.
Leiming Du +4 more
semanticscholar +1 more source
Crack initiation mechanisms under two stress ratios (R = − 1 and 0.5) and up to very-high-cycle fatigue (VHCF) regime of a selective laser melted (SLMed) Ti-6Al-4V were investigated.
Leiming Du +4 more
semanticscholar +1 more source