Results 101 to 110 of about 101,004 (302)
Shock compression response of high entropy alloys
, 2016 In this work, we studied the shock response of two typical equiatomic high entropy alloys (HEAs) (i.e. FCC-structured CrMnFeCoNi alloy and BCC-structured NiCoFeCrAl alloy).
Dai, LH (reprint author), Chinese Acad Sci, Inst Mech, State Key Lab Nonlinear Mech, Beijing, Peoples R China. +6 more
core +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Review of Creep Cavitation and Rupture of Low Cr Alloy and its Weldment [PDF]
, 2013 This paper presents a review of creep cavitation and rupture of low Cr alloy and its weldment, particular in the heat-affected zone (HAZ). Creep damage is one of the serious problems for the high temperature industry.
Xu, Qiang +6 more
core +1 more source
, 2022 We present a combined experimental and computational investigation of the mechanical properties of a CoCrFe0.75NiMo0.3Nb0.125 (composition in molar ratio) high-entropy alloy additively manufactured via cold spray.
Ponga, Maricio +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Lattice Distortion in High-Entropy Alloys
Journal of Materials Research, 2018 Abstract
Owen, Lewis Robert +1 more
openaire +2 more sources
Microstructure and properties of welds between 5754 Al alloys and AZ31 Mg alloys using a Yb:YAG laser [PDF]
, 2014 The authors wish to thank Mr. Henri ANDRZEJEWSKI for his technical assistance in laser experiments. The authors wish to place their sincere thanks to Professor Philippe BOURNOT and Dr.
BANNOUR, Sana +9 more
core +1 more source
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
High-entropy alloys - microstructures and properties
, 2015 There are relatively few revolutions in the venerable and rather staid field of metallurgy. One can count among them the advent of metallic glasses, of superplastic metals, of memory-alloys and - on the purely theoretical side - of quasicrystals.
Fisher, David J. 1947-
core