Results 181 to 190 of about 22,260,269 (238)

PM Magnetization State Estimation Based on PM High Frequency Resistance Using High Frequency Signal Injection

open access: yes, 2016
Permanent magnet (PM) magnetization state estimation is important both for torque control and monitoring in conventional permanent magnet synchronous machines (PMSMs). Furthermore, this can be critical for variable flux machines (VFM). Use of high frequency signal injection methods for PM magnetization state estimation in NdFeB magnets has already been
Fernández Alonso, Daniel   +4 more
openaire   +2 more sources

Active islanding detection using high frequency signal injection

2011 IEEE Energy Conversion Congress and Exposition, 2011
Islanding detection is of great importance for reliable operation of smart grids. Islanding-detection methods can be classified into three different groups, i.e., active, passive, and communication-based methods. Active methods inject a disturbing signal (typically a voltage) and analyze the system response (typically in the current).
David Reigosa   +4 more
openaire   +1 more source

Current Measurement Gain Tuning Using High Frequency Signal Injection

2007 IEEE Industry Applications Annual Meeting, 2007
Accurate measurement of the phase currents in electric machines is a requirement for most high performance drives. Incorrect current measurement gain estimates, caused by device tolerances, temperature drifts, age and noise, reduce the accuracy of the current measurements and degrade the drive's performance.
Michael C. Harke   +4 more
openaire   +1 more source

Applications of high frequency signal injection in non-linear systems

International Journal of Control, 1977
Abstract High frequency signal injection (dither) has found applications in control and stabilization, adaptive systems, identification and quantization. A discussion of typical uses is given and analyses are presented using the concept of equivalent non-linearity.
R. J. SIMPSON, H. M. POWER
openaire   +1 more source

Modeling of Saturated Induction Machines With Injected High-Frequency Signals

IEEE Transactions on Energy Conversion, 2007
This paper analyzes the effects of injecting additional signals in induction machines for the purpose of speed control. A new saturation model able to correctly model the interaction between the added signal and saturation of the motor core due to the main torque-producing flux is presented.
Giovanni Bottiglieri   +2 more
openaire   +1 more source

Sensorless drive of SMPM motor by high frequency signal injection

APEC. Seventeenth Annual IEEE Applied Power Electronics Conference and Exposition (Cat. No.02CH37335), 2002
This paper represents a new sensorless control scheme of surface mounted permanent magnet (SMPM) motors. To estimate the rotor position of the SMPM motor, a high frequency voltage signal is injected and the resultant injected frequency current signal is used.
null Ji-Hoon Jang   +4 more
openaire   +1 more source

Islanding Detection in Three-Phase and Single-Phase Systems Using Pulsating High-Frequency Signal Injection [PDF]

open access: yesIEEE Transactions on Power Electronics, 2015
This paper analyzes the use of pulsating high-frequency signal injection for islanding detection purposes. Active islanding detection using high-frequency signal injection is an appealing option due to its reduced nondetection zone, reduced cost, and ...
Juan Manuel Guerrero   +2 more
exaly   +2 more sources

Exploring node interaction relationship in complex networks by using high-frequency signal injection

Physical Review E, 2021
Many practical systems can be described by complex networks. These networks produce, day and night, rich data which can be used to extract information from the systems. Often, output data of some nodes in the networks can be successfully measured and collected while the structures of networks producing these data are unknown.
Xinyu Wang   +5 more
openaire   +2 more sources

Sensorless field-orientation control of an induction machine by high-frequency signal injection

IEEE Transactions on Industry Applications, 1997
This paper describes a new scheme to find the rotor flux angle from stator voltages and currents by injecting a high-frequency signal. The signal is not a rotating one but a fluctuating one at a reference frame rotating synchronously to the fundamental stator frequency.
null Jung-Ik Ha, Seung-Ki Sul
openaire   +1 more source

High Frequency Torque Ripple Suppression for High Frequency Signal Injection Based Sensorless Control of SynRMs

2019 IEEE Applied Power Electronics Conference and Exposition (APEC), 2019
The main limitation for the wide application of synchronous reluctance motors (SynRMs) is the torque ripple caused by the special structures and control method. To lower the cost of SynRM drive system and expand speed range of SynRMs, high frequency signal injection (HFSI) is an effective sensorless control scheme for SynRMs to achieve low and zero ...
Chengrui Li   +3 more
openaire   +1 more source

Home - About - Disclaimer - Privacy