Results 91 to 100 of about 118,466 (337)
Development of a super ductile diecast Al-Mg-Si alloy [PDF]
, 2012 This is the post-print version of the final paper published in Materials Science and Engineering A. The published article is available from the link below.
Fan, Z, Watson, D, White, M
core +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Preparation of Cu-based bulk metallic glasses by suction casting [PDF]
, 2007 A series of Cu-Hf-Ti alloys prepared by rapid solidification of the melt and by copper mould casting were studied in the present work. Alloy ingots were prepared by arc-melting mixtures of pure metals in an argon atmosphere.
Carroll, P.A. +4 more
core
Spinning of hollow fiber ultrafiltration membranes from a polymer blend [PDF]
, 1995 In this study the dry-wet spinning technique is used for the preparation of hollow fiber membranes. In the polymer solution a blend of two polymers, poly(ether sulfone) and poly(vinyl pyrrolidone), is used.
Boomgaard, Th. van den +3 more
core +2 more sources
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Tailoring flow behavior and heat transfer in tempering channels for high pressure die casting – Analysis of potentials of commercial static mixers and prospects of additive manufacturing [PDF]
, 2022 Marco Sode +6 more
openalex +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Kaedah pembelajaran lukisan kejuruteraan berasaskan simulasi [PDF]
, 2004 Kajian yang dijalankan ini adalah untuk melihat kebolehgunaan sebuah perisian pendidikan yang menerapkan Kaedah Pembelajaran Lukisan Kejuruteraan Berasaskan Simulasi bagi menyelesaikan masalah kurang faham , kurang minat dan kebergantungan yang terlalu ...
Darmin, Darni
core
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Refinement of primary Si in hypereutectic Al-Si alloys by intensive melt shearing [PDF]
, 2012 Hypereutectic Al-Si based alloys are gaining popularity for applications where a combination of light weight and high wear resistance is required. The high wear resistance arising from the hard primary Si particles comes at the price of extremely poor ...
Anuradee T +10 more
core +1 more source