Results 101 to 110 of about 85,615 (303)
An Initial Assessment of Infiltration Material Selection for Selective Laser Sintered Preforms [PDF]
, 2004 High-temperature infiltration is an important process that is used to add strength to skeletal microstructures. In this study, particulate metal matrix composites (MMCs) are fabricated.
Barrow, Stacia L. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
Experimental and optimization study of powder metallurgy process parameters of magnesium base AZ31 alloy using taguchi method [PDF]
Engineering and Technology JournalPowder metallurgy (PM) is a highly effective re-processing method mostly used for magnesium-base alloys, especially in high-performance Mg alloys. In the present work, the experimental and optimization of PM process parameters, including compaction ...
Basma Sultan +3 more
doaj +1 more source
Thermal Modeling of Metal Powder-Based Selective Laser Sintering [PDF]
, 2005 In order to get a better understanding of Selective Laser Sintering (SLS) process of the metal powders, three-dimensional modeling of laser sintering of a metal powder mixture that contains two kinds of metal powder with significantly different melting
Chen, Tiebing, Zhang, Yuwen
core +2 more sources
Advanced Engineering Materials, EarlyView.New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold +2 more
wiley +1 more source
Effect of Ultra-High Pressure Sintering and Spark Plasma Sintering and Subsequent Heat Treatment on the Properties of Si3N4 Ceramics. [PDF]
Materials (Basel), 2022 Lv X, Li X, Huang J, Ge C, Yu Q.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Ca-looping for postcombustion CO2 capture: A comparative analysis on the performances of dolomite and limestone [PDF]
, 2015 The low cost and wide availability of natural limestone (CaCO3) is at the basis of the industrial competitiveness of the Ca-looping (CaL) technology for postcombustion CO2 capture as already demonstrated by ~1Mwt scale pilot projects.
Pérez Maqueda, Luis Allan +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz +6 more
wiley +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Advanced Engineering Materials, EarlyView.Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source