Solidification behaviour and mechanical properties of cast Mg-alloys and Al-based particulate metal matrix composites under intensive shearing [PDF]
, 2011 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Magnesium alloys, as the lightest of all structural metallic materials, and aluminium-based particulate metal matrix composites (PMMCs), offering unified ...
Tzamtzis, Spyridon
core +7 more sources
Arc welding of high strength aluminium alloys for armour systems applications [PDF]
, 2011 The ternary Al-Cu-Mg system 2xxx series aluminium alloys were examined as construction materials for armour system applications based upon comparable ballistic properties to the currently employed Al-7xxx series alloys.
Pickin, Craig Graeme
core +7 more sources
Corrosion of indium doped E-AlMgSi aluminum conductor alloy (Aldrey) [PDF]
Modern Electronic Materials, 2021 The effect of impurities on the electrical conductivity of aluminum has been studied in detail. The electrical conductivity of aluminum is 65.45% of that of copper.
Izatullo N. Ganiev +4 more
doaj +3 more sources
Research status of selective laser melting aluminum alloys
Fenmo yejin jishu, 2021 Selective laser melting (SLM) technology has been widely applied in the industry due to its customization, short manufacturing cycle, and high precision. The research progress of aluminum alloys and composites prepared by SLM was systematically reviewed.
WU Ling-zhi +4 more
doaj +1 more source
Effect of calcium doping on the anodic behavior of E-AlMgSi (Aldrey) conducting aluminum alloy in NaCl electrolyte medium [PDF]
Modern Electronic Materials, 2023 The design of new materials intended for operation under severe conditions faces the task of rendering the materials corrosion resistant. The practical solution of this task is interrelated with the knowledge of corrosion protection of metals and alloys.
Izatullo N. Ganiev +3 more
doaj +3 more sources
Cold cracking in DC-cast high strength aluminum alloy ingots: An intrinsic problem intensified by casting process parameters [PDF]
, 2011 For almost half a century the catastrophic failure of direct chill (DC) cast high strength aluminum alloys has been challenging the production of sound ingots.
A. Ten Cate +27 more
core +2 more sources
A probabilistic model for the high cycle fatigue behaviour of cast aluminium alloys subject to complex loads [PDF]
, 2013 Lien vers la version éditeur: http://www.sciencedirect.com/science/article/pii/S0142112312002472This article is dedicated to the high cycle fatigue behaviour of cast hypo-eutectic Al–Si alloys and in particular the AlSi7Cu05Mg03 alloy.
PESSARD, Etienne +3 more
core +1 more source
Study of Hydrogen-Induced Plastic Damage Response of 7085-T7651 High-Strength Aluminum Alloy
Metals, 2022 The hydrogen-induced plastic loss behavior of titanium alloys is often reported, but there are relatively few studies on high-strength aluminum alloys.
Xiao Yang +6 more
doaj +1 more source
Potential fatigue strength improvement of AA 5083-H111 notched parts by wire brush hammering: Experimental analysis and numerical simulation [PDF]
, 2014 The effects of milling as machining process and a post-machining treatment by wire-brush hammering, on the near surface layer characteristics of AA 5083-H111 were investigated.
SIDHOM, Habib +4 more
core +1 more source
Anode behavior of aluminum alloy AB1 with magnesium [PDF]
E3S Web of Conferences, 2023 In modern technology, the main advantages of aluminum alloys as structural materials are lightness, pliability to stamping, corrosion resistance (in air, aluminum is instantly covered with a strong film of Al2O3, which prevents its further oxidation ...
Kurbonova M. Z. +5 more
doaj +1 more source