Results 91 to 100 of about 813,621 (310)
Arthritis Care &Research, Accepted Article.Purpose The study aimed to identify symptom‐based predictors of dry eye disease (DED) signs in the Sjögrens International Collaborative Clinical Alliance (SICCA) cohort. Methods Retrospective analysis examining 16 ocular symptoms (most graded 0‐4) and artificial tear (AT) use (graded 0‐3) as predictors of DED signs [abnormal ocular surface staining ...
Pragnya R Donthineni +7 more
wiley +1 more source
Methodology for determining the bearing capacity of tensioned tubular reinforced concrete elements
Budownictwo o Zoptymalizowanym Potencjale EnergetycznymConstructive solutions for tensioned concrete-filled steel tubular (CFST) elements can be applied in bar systems (trusses, arches, frames, structural and cable-stayed structures, radio and television towers, as well as other similar applications) and can
Roman Shmyh +3 more
doaj +1 more source
The influence of heat treatment on homogeneity of strength properties and structural peculiarities of low-carbon steel Fe-Mo-Nb-V-C processed by high-pressure torsion [PDF]
, 2000 A homogeneity of strength properties (microhardness) through the specimens and the peculiarities of an ultrafine-grained structure produced in low-carbon steel Fe-Mo-Nb-V-C by cold high-pressure torsion, depending on initial heat treatment of steel were ...
Astafurova, Elena +8 more
core +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Effect of Cr on Process and Mechanical Properties of Ultra-high Strength Cord Steel LX82A
Teshugang, 2023 The effect of Cr element in ultra-high strength cord steel on the microstructure and properties of LX82A wire rod and drawn wire is studied by JMatPro software， metallographic microscope， scanning electron microscope and tensile properties test.
Song Yancheng +4 more
doaj
Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control
Advanced Engineering Materials, EarlyView.This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian +4 more
wiley +1 more source
Stress corrosion cracking susceptibility of 18 Ni maraging steel [PDF]
The stress corrosion cracking (SCC) resistance of 18Ni maraging steel (grades 200, 250, 300, and 350) was determined in 3.5 percent salt (NaCl) solution, synthetic sea water, high humidity, and outside MSFC atmosphere.
Humphries, T. S., Nelson, E. E.
core +1 more source
Hot ductility and deformation behavior of C-Mn/Nb-microalloyed steel related to cracking during continuous casting [PDF]
, 2014 Hot ductility studies have been performed on C-Mn and C-Mn-Nb steels with an approach to simulate the effect of cooling conditions experienced by steel in secondary cooling zone during continuous casting.
Lanjewar, Harishchandra +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
Development of CrNiMo-CrNi3Mo-CrNiMo Triple-Layer Clad Ultra-High Strength Steel Plate
Teshugang, 2020 In order to develop low alloy ultra-high strength steel with super high strength and good toughness, a 15 mm CrNiMo-CrNi3Mo-CrNiMo triple-layer clad ultra-high strength steel is developed by 30MnCrNiMo steel billet and 33MnCrNi3Mo steel ingot, the ...
李雷 +5 more
doaj