Results 141 to 150 of about 813,621 (310)

Optimization and analysis of cutting parameters using cryogenic media in machining of high strength alloy steel [PDF]

, 2013
In this research, liquid Argon is used as a cryogenic media to optimize the cutting parameters for evaluation of tool flank wear width of Tungsten Carbide Insert (CNMG 120404-WF 4215) while turning high strength alloy steel.
Ali, Liaqat, Butt, Shahid, Jaffery, Husain, Jaffery, Mehdi, Khan, Mushtaq, Tahir, Waseem   +5 more
core  

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Experimental X-ray Stress Analysis Procedures for Ultra High Strength Materials [PDF]

X-ray stress analysis procedures for accurate measurement of elastic strain in high strength ...
Barkley, W. J., III, Clough, W. R., Jackman, L. A., Reilly, F. P., III, Woehrle, H. R.   +4 more
core   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source