Results 131 to 140 of about 922,426 (306)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Simulation Analysis of Non-Pneumatic Tire Wear Based on Temperature-Corrected Archard Model
MachinesNon-Pneumatic Tires (NPTs) have been recognized for their advantages, such as low rolling resistance, burst resistance, and lightweight design, which make them highly suitable for application in electric vehicles under complex conditions, including high ...
Haoze Ren +4 more
doaj +1 more source
Journal of Physics: Conference SeriesAbstract Internal gear transmission, boasting advantages such as compact structure, high transmission efficiency, and strong load-carrying capacity, is widely applied in high-end equipment fields, including aerospace, precision machine tools, and new energy vehicle transmission systems.
Yongjie Bao +4 more
openaire +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Design and evaluation of high contact ratio gearing
, 1986 Scoring test and surface fatigue tests were conducted on spur gears of a standard design and spur gears of a high contact ratio design. All testing was conducted in the Sikorsky 6-inch dynamic test facility at a speed of 8000 rpm using 23699 oil.
Frint, Harold K.
core
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Research on load coefficient for high contact ratio high-gears based on strain testing
Journal of Physics: Conference SeriesAbstract Regarding the issue of no standard basis for selecting the load coefficient in the design of high-gears, this paper uses the resistance method to measure the strain at the root of high-gear by building a test rig, and obtains the variation law of tooth root strain under different torques and speeds.
Yi Liu +5 more
openaire +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source