Results 151 to 160 of about 131,294 (264)

Light‐Programmable Interfaces: From Molecular Photoswitching to Adaptive Membrane Separations

Advanced Materials Interfaces, EarlyView.
This review advances an interface‐centered framework for light‐responsive membranes, linking molecular photoswitches (azobenzene (AZO), spiropyran (SP), diarylethene (DAE), donor–acceptor Stenhouse adducts (DASA), photoacid) to integration strategies in polymeric, porous, self‐assembled, and mixed‐matrix systems.
Liangliang Zhang, Senlin Gu, Jianyang Zhao, Xiaojuan Hao, Lu Hua Li, Jihua Li, Lingxue Kong   +6 more
wiley   +1 more source

Effect of Hydrogen on High Cycle Fatigue Properties of L360 Pipeline Steel Notched Specimens. [PDF]

Materials (Basel)
Huang L, Zhang L.
europepmc   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

Observation and modeling of potential sub-threshold damage growth mechanism for nitinol in ultra-high cycle fatigue. [PDF]

Int J Fatigue
Roiko A, Cook S, Berg B, Falk W, Weaver JD.   +4 more
europepmc   +1 more source

Hydrogel‐Based 3D‐Printable Stretchable Pressure Sensor

Advanced Materials Technologies, EarlyView.
We present a carbon‐black‐functionalized double‐network granular hydrogel (DNGH) pressure sensor capable of detecting pressures from 200 Pa, equivalent to a light finger touch, up to 500 kPa. The sensor exhibits signal drifts below 3.5% after 800 cycles and response times around 80 ms. Leveraging this broad sensing range, we 3D print this material into
Tianyu Yuan, Chenzhuo Li, Antonia Georgopoulou, John M. Kolinski, Esther Amstad   +4 more
wiley   +1 more source

AI-Powered Very-High-Cycle Fatigue Control: Optimizing Microstructural Design for Selective Laser Melted Ti-6Al-4V. [PDF]

Materials (Basel)
Awd M, Walther F.
europepmc   +1 more source

Data analysis of high-cycle fatigue testing on piston aluminum-silicon alloys under various conditions: Wear, lubrication, corrosion, nano-particles, heat-treating, and stress. [PDF]

Data Brief, 2022
Azadi M, Parast MSA.
europepmc   +1 more source

Lattice Structures for Bone Replacement: The Intersection of Bone Biomechanics, Lattice Design, and Additive Manufacturing

Advanced Materials Technologies, EarlyView.
This review outlines how understanding bone's biology, hierarchical architecture, and mechanical anisotropy informs the design of lattice structures that replicate bone morphology and mechanical behavior. Additive manufacturing enables the fabrication of orthopedic implants that incorporate such structures using a range of engineering materials ...
Stylianos Kechagias, Maxwell J. Munford, Frederik C.H. Masure, Richard J. van Arkel, Reece N Oosterbeek   +4 more
wiley   +1 more source

Scaling of damage mechanism for additively manufactured alloys at very high cycle fatigue. [PDF]

Sci Rep
Voloskov BS, Bannikov MV, Bayandin YV, Naimark OB, Sergeichev IV.   +4 more
europepmc   +1 more source

Roll‐to‐Roll Manufacturing of Flexible Thermoelectric Semiconductors Using Low‐Level Direct‐Current Sputtering

Advanced Materials Technologies, EarlyView.
Roll‐to‐roll direct‐current sputtering enables room‐temperature manufacture of flexible bismuth telluride thermoelectric films. By identifying a low‐power deposition window that suppresses charge‐induced arcing, this work links sputtering conditions to film structure, charge transport, and thermoelectric performance, achieving a room‐temperature figure
Xudong Tao, John O'Sullivan, Kening Wan, Emiliano Bilotti, Ruy Sebastian Bonilla, Hazel E. Assender   +5 more
wiley   +1 more source